Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hi,
I'm working on a project using MCUboot, TFM, and a network core app. We use MCUboot with an external flash module for OTA firmware updates.
Recently, we tried upgrading...
Hi,
I am following DevAcademy Lesson 5, HTTP over Wi-Fi (Exercise 2), which involves adding TLS to an HTTP connection.
When I remove CONFIG_WPA_SUPP_CRYPTO_PSA=y , I am...
Using an nRF54L15 here (if that matters) and adding mcuboot via sys build to my project. Couple questions:
- How would one adjust the logger baud rate to something other...
Hello,
I have the nRF5340 DK and I want to program/debug an external SoC. I see that in order to do that I can use the connector P19 to connect to an external board with...
I am using an nrf5340 DK instead of the audio DK. Is BT LE possible with this DK. Is there any difference beween NRF5340 DK and audio DK in terms of microntroller.
Hello,
I’m using VS Code with the nRF Connect extension. When I try to build the “bme68x_iaq” application to upload it later to the Nordic Thingy:53 and read its data, I...
Hi,
I have verified the firmware upgrade and file transfer functionality from a Linux-based device to the customized nrf52840 board using the mcumgr tool.
However, the...
Hello, everyone!
I'm interested to know about the possibility of mixing BLE audio and custom BLE Characteristic in one single nRF5340 application.
For example, we would...
Hi DevZone Community,
My Envriornment
1.9.1 NCS nRF9160DK Current Modem Version : 1.3.2 This question is involving a device which is in production. The issue is, if the...
Hi folks,
Recently picked up a new MacBook (M series) and was excited to try some sample projects on my nrf52840dk.
Unfortunately upon trying to Debug, I get the following...
Hello Nordic team,
I followed the official guide to add a custom sensor cluster to my Matter application. Everything built and flashed successfully, and the application...
hello, i have a weired issue with my sensor communication using spi. the code that used the old SDK works, but the one using the new SDK for some reason doesnt. i need to...
Hi,
iam completely new for NRF soc.i want to develope a application where i want to configure the dev name,tx power while run time via mobile application. please tell me...
Currently, we've started developing a new project using the nRF52832 as our controller. Our requirement is quite simple: we need to list out nearby advertising BLE devices...
Hi.
I am using a custom board on an nRF52810 microcontroller and a LIS2DH12 accelerometer connected to it via SPI. SDK version 2.7.0.
Here's my settings:
.dts file ...
