Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
I was trying to get a simple Zephyr project to build and run on the Arduino Nano BLE 33 which has a NRF5248.
In VSCode with the NRF plugin I select "Add build configuration...
I have a PCA10056 (nRF52840 DK) and while programming it with a UART example from the nRF5_SDK_17.1.0_ddde560 using Segger Embedded Studio for Arm 5.42a, it will not show...
Hello, I have one smartphone with Android and one ith iOS with NRF connect application and I can't see, only on iOS, the Primary and secondary PHY used by my advertiser device...
Hi everyone,
We have devices using the BLE module (nRF52) deployed in clinics for testing. They have been functioning without issues until recently when we noticed occasional...
I'm using the nRF54L15-DK to run a Bluetooth peripheral_hr project in DCDC mode, but if I write
nrf_regulators_vreg_enable_set(NRF_REGULATORS, NRF_REGULATORS_VREG_MAIN,...
Context: I am working on a project to monitor up to 880 devices in an Industry 4.0 warehouse. The warehouse is divided into 16 areas, with each area housing 30–55 devices...
Hi everyone,
I’m a complete beginner and need some help. I’m working with two XIAO nRF52840 Sense boards: one as a central and the other as a peripheral. My goal is to send...
Hi,
I am trying to use a digital channel to sync with a current measurement. I have connected VCC, GND and a digital output of my DUT to the PPK2. I can see from the scope...
I am evaluating a Fanstel BC805M device, which uses the nRF52805 chipset. I am using VSCode and have installed the nRF Connect Extension Pack, toolchain v2.8.0, and SDK v2...
I programmed a nrf52840dk board (PCA10056 3.0.0 2022.7 1050288497) as a sniffer. It works well.
Now I want to flash it to zephyr samples/basic/blinky by "west flash". west...
Hi,
(nrf52840, custom device, nRF5_SDK_15.3.0_59ac345)
I am working on a BLE project involving one central device and two peripheral devices using BLE NUS. The peripheral...
Issue with debug on the PDK eng_rev_B PCA10156
Segger does not recognize the chip and debug fails across multiple sample applications
debug message results:
JLinkGDBServerCL...
Hello,
We are investigating a compatibility issue between our devices running nRF5 SDK 12.3.0 with softdevice s332 v2.0.0 and a Motorola Edge 50 smartphone. From BLE sniffer...
Hello,
Does the nRF54L15 have multipoint?
In my application, I would like to have different devices connected simultaneously, so I was looking for something like multipoint...
