I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hi
Seems like all new nRF DKs shipped with nRF5340 as interface mcu have limited speed on Debug Out.
nrfjprog -r --clockspeed 646 Applying system reset. Run. nrfjprog...
I need to send a JWT to a non-nordic server. They ask for a small struct to be encoded and sent as a string in a larger MQTT message. For example:
That struct is encoded...
I have flashed the light_ctrl hex file in nrf52840 dongle. Flashing Have been completed sueccessfully for provisioning in nrf mesh application its not showing in the network...
Hello,
For a Uni Project I want to measure the current of the Nordic Thingy:91 and visualize it. Therefore i bought the Power Profiler Kit 2. But i dont know how to connect...
So when changing the hci_icp.conf settings to have the configuration below, i get "CMake Error at C:/ncs/v2.6.1/zephyr/cmake/modules/kconfig.cmake:358 (message):" plus the...
My device is peripheral. I added a few lines before the advertisement start in main(). The whole project is in main and simply advertise and get connected and bonded.
...
I want to configure the ESB and nRF21540 chips on the NRF21540-DK. In order to compare the signal gain, I used the nRF52832-DK and burned the Bluetooth routine (without any...
Hello,
I have a project working on Nora B1, which I am testing on nrf5340DK. It is based on the Peripheral UART Sample, programmed with nfr Connect SDK v1.9.1. Now I need...
Hello,
This is probably a dumb question but, I'm having issues with an initial prototype for a product that has been given. The hardware engineer (me) designed and got...
Quick Start can see the board - but says 'Not supported yet'
Load the programmer and select my board: The log looks like this:
19:07:18.801
Initialising nrfutil...
Hi everyone,
I am testing modem shell application (2.6.1) for PPP support.
Here I am building the application using overlay-ppp.conf and ppp.overlay files.
after flashing...
Hello,
I am currently developing a product that is based on a nrf9160 and more precisely with a Thingy:91, this project integrates the tools of Golioth to communication...
Good morning!
I already looked at other questions in the forum but couldn't find any help. I'm trying to implement an example of Https with basic authentication on my nrf9160dk...
Dear sir:
The DAC private key is generated using P256, and the key length is 256 bits, which is 32 bytes.
As below link, why is 68 bytes planned in the factory data? ...
I'm following Intermediate course lesson 1 exercise 2 to use guiconfig.
When I try to open guiconfig,the output in terminal as follow:
How can I fix it?
