I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I have ordered two boards using the nrf52840
I was able to flash the first board and my firmware is working as expected however whenever I try to program the other one I...
When uploading a network core image though MCUBoot and confirming the image, sometimes it fails to accept and on other builds it accepts the update.
I have narrowed this...
Hi
Greetings, Hope you are doing well.
I am fairly new to using the nRF Connect SDK through VS Code. I completed the nRF Connect SDK Fundamentals course, and I also noticed...
Hi All,
I am currently working on an project with the nRF9151 using the nRF SDK v3.1.1 and MCUboot and I need to sign my application images using an external HSM. I am using...
I am having this problem in my Macbook Air M4. It times out when flashing the application via nRF Connect SDK extension. I also tried to run the nrfjprog command myself and...
I’m evaluating the nRF Connect SDK Bare Metal SDK and hit an issue with the bm_storage library. bm_storage_write() and bm_storage_read() work correctly, but bm_storage_erase...
When using GNSS periodic mode with nrf_modem_gnss_fix_interval_set() set to 20 minutes and nrf_modem_gnss_fix_retry_set() to 5 minutes, the actual wake-up intervals are inconsistent...
Hi,
I have a feeling we may be experiencing Modem Reset Loop Restrictions on some of our devices, so I want to put in something to our application code so we know and can...
Hi ,
I need to do create the bootloader . generally what we dump in to the board was the firmware not bootloader right. I want to do the OTA updates on the nRF52840 Dev...
Hello,
I am currently using nRF Cloud to perform FOTA updates on my nRF9160 devices. I have multiple certificates on this device.
1. TLS certificate for my application...
I need to store a hardware-revision value on an nRF9160 during manufacturing (using something like nrfjprog ), and the non-secure application firmware must be able to read...
Hi
I’m working with an NPM1300EK connected over I²C to an nRF54L15 , and I’m seeing an issue where the VBUSINSTATUS register consistently reads back 0x00 , even when VBUS...
Hi,
I’m working on nRF9151 with nRF Connect SDK 2.9.0 , and I’m facing a FLASH overflow issue when enabling dual-image OTA (primary + secondary partitions) . Our project...
Issue Summary
fds_record_update() in SDK 13.0.0 creates permanent duplicate records instead of replacing old records. This causes:
Valid record count to grow indefinitely...
Hi Nordic support:
Our project uses the nRF9151 and QM13545 MIPI RF SWITCH. We have a question about AT%XMIPIRFFECTRL command's frequency: If the frequency switching point...
