I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Dear Customer Support,
We are gathering the list of supported AT commands support for the nRF9151
Also experimenting available AT commands using the nRF9151DK
So far...
I’m trying to build and flash a BLE Mesh DFU application for the nRF5340 DK board, but it isn’t working. I selected the nrf5340dk_nrf5340_cpuapp build target only. Could you...
Hello,
I’m developing a composite USB device on nRF5340 (NCS v2.6.0) that exposes USB CDC + MIDI + Audio. When using the USB Audio interface, volume control works correctly...
I am trying to reset an nRF52840DK - it is visible within the nRF Connect SDK in Visual studio code but gives a timeout message:
[14:27:11] nrfutil-device reset --serial...
Hi everyone,
I’m currently working on a small, battery-powered tracking device based on the Nordic nRF9151 SiP . The goal is to create a compact and energy-efficient product...
I am unable to program the Thingy:91 using nRF Connect for Desktop → Cellular Monitor application , as described in the following link:
https://academy.nordicsemi.com/courses...
Hi,
what is the recommended way on the nRF91x1 to clear the Forbidden PLMN list?
Devices may get denied on networks repeatedly, filling up the FPLMN list. To ensure the...
Hi, we are still struggling with nrf9161 behavior and trying to mitigate data sending dropouts ( and ).
Here is one partial issue: we are currently using UDP and flushing...
using west update i just update the old version 3.0.2 to 3.1.1 and after take blinky code and build then i have got below error,also using the vs code i doenload the NCS v3...
Hello, While designing the hardware circuit for the CAAA WLCSP with internal LDO regulator setup on the nrf52810, I removed the 32.768kHz crystal oscillator and retained only...
I am currently developing my project using the nrf52832 and the nrf5SDK.
I utilized the peer_manager module, and in the application, when being connected as a peripheral...
Hi,
I’m using an nRF5340DK with nRF Connect SDK 2.9.1 , configured as both Central and Peripheral with the nordic SDC running the network processor Goal: allow the board...
The High-Performance Framework (HPF) is a framework designed to support the development and integration of software peripherals using coprocessors (e.g. FLPR on RF54L15)....
Hi,
I managed to get Channel Sounding with Pixel 10 as Initiator working, based on this change on mainline.
https://github.com/nrfconnect/sdk-nrf/commit/30f67fc0b6be8051b5d8f73d900675dd98758631#diff...
Hello Nordic team,
I'm developing a BLE peripheral using nRF52833 and would like to validate that my approach for handling connection parameters aligns with Nordic's best...
