Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
Hi,
We have been trying to get the audio application to work using an external I2S microphone, but have recently run into the following problem when trying to send audio...
Hello Nordic,
I've been attempting to convert our system's TWIM implementation from the blocking to the non-blocking mode. I have been able to communicate fine with the...
Hi,
I have updated finally Segger Studio from version 7.22 to 8.14. Now I cannot compile the project. It ends with below error:
Build failed, exit status 0x1
Is something...
Hi, I have a problem where the mcuboot do not seem to include the 'jedec,spi-nor' driver. Looking at the build directory, /build/zephyr/zephyr.dts file has the device spi...
Hello everyone
our current project is to use dht22 to control an external fan
but we don't know how to add a new node to the device tree for the fan.
The picture below...
I got the license key for segger studio but the option to install the license is not popping up. https://drive.google.com/file/d/1qok8PcCYhHi_9nsknL2JW4_AtF6F5ZP5/view?usp...
Hello I have a few questions
In my project, the nPM1300 fuel gauge example via nrf5340dk works properly. I received information such as V - I - SOC via I2C. Currently I...
I try to use Gazell and USB HID to remote wake up my computer. But after compter turns into sleep, the callback function on the Gazell Host Device doesn't being called back...
The hardware I use is nrf52840Dongle, using nrf_dm sample for development. There are a few problems:
1. I have 8 devices, all within communication range, 4 as base stations...
Hi, I get a issue, build error if enabled PGPS in prj.conf:
CONFIG_NRF_CLOUD_PGPS =y
and OK if comment this config
for this project, I used sample/cellular/Location...
I've tried to compile "hello_dect" example using v2.6.1 toolchain and v2.7.0-rc-2 SDK. The sample code is present so I assume the SDK is correct version. However it fails...
Hi,
For some reason, all of the VSCode action disappears after building the application with mcuboot using sysbuild on ncs 2.7.0. The application can only be built using...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
OK, I'm working with the nRF52832 and NCS V2.6.0, and I have two different actions I need to complete at various times with the SAADC:
Every ~ 3 seconds, I need to sample...