Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
i have a "bare-metal" (register-level access) BLE advertising program which does not consistently consume the same amount of power when transmitting.... here's what the power...
Hi,
I had some issue with my nRF52 DK PCA10040 v3.0.3, The programmer was totally unreachable also with the simplest terminal command so I tried to reprogram it trough hidden...
I am trying to implement GPS code in the nrf9160 but I cant find the function nrf_modem_gnss_init(); to initialize GNSS inside the modem in , is it being initialised within...
The following log is a compilation error.Is there any way to correctly compile?
e:/nordic/ncs/toolchains/fd21892d0f/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr...
We have an application where response time is critical, and we are trying to minimize the time from advertising to an active channel sounding session.
What we have already...
Dear Nordic,
We are currently evaluating the Amarisoft CallBox as an end-of-line (EoL) testing tool.
In an ideal scenario, we would like to use 1NCE production SIM cards...
When performing FOTA using NCS 2.9.2, we observed that the swap using move process takes approximately tens of seconds. However, with NCS 3.2.4, the same swap using move operation...
nRF Connect SDK v3.2.3, nRF9160.
Hi,
I'm working on a project which has MCUBoot enabled (dual slot) for firmware updates over cellular connection. I did not have a pm_static...
Hello,
I want to program the bare nRF52832 MCU over SWDIO, SWCLK, GND and +3,3V Connections with a Segger J-Link programmer. Unfortunately the programmer could not connect...
We are experiencing an issue with the QSPI driver on nRF54L15 where external flash access stops working after a BLE bonding procedure.
The system works correctly until bonding...
Is it possible to be able to get hold of some of the legacy software for the nRF52 BLE sniffer that works off the old nRF Command Line Tool rather than the nRFutil? As I'm...
Hello together!
I am trying to reproduce the ultra low power connection as described in this whitepaper: /cfs-file/__key/communityserver-discussions-components-files/4/3482...
Hi,
I am working on a smartwatch PoC using the nRF7002 DK (nRF5340), and I am trying to interface a 1.8" ST7735 SPI TFT display (128x160).
Hardware: - Board: nRF7002DK...
Ultrasonic welding is commonly used to seal plastic enclosures for electronic devices. 32kHz crystals can be damaged by this type of welding and manufacturers recommend not...
