Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hello,
I am trying to adapt the "Interfacing with a sensor over SPI" example from the nRF Connect SDK Intermediate Dev Academy course in Lesson 5. When I run the code as...
Since it was brought up in the Webinar today, that the nRF54LM20A is not recommended for use with LE Audio due to the lack of an Audio PLL, I was wondering that the Audio...
Hi Nordic Dev,
We are experiencing issues with sudden connectivity loss and hardlocked devices 1,5 years after product launch. We are currently suspecting the flash storage...
Hello,
I have a Thingy:91x.
I flashed a BLE central program to the nRF5340 on this device.
However, I get an error initializing BLE. I've confirmed that this program...
Board/Setup:
Board: nRF9151 DK / nRF9151 SoC
Peripheral: External BLE module connected via UART1
Use case: BLE module is only needed during commissioning...
Hi there,
I have been trying to implement a low-power mode that basically suspends UART, I2C, etc before entering sys_poweroff() when critical battery level is triggered...
Hi,
I have several field devices using the LTE Link Controller library with nRF Connect SDK v2.5.1. Most of them work fine — they are programed to connect every hour. However...
Greeting Nordic Expert !
I would like to override the following hook in MCUboot:
int boot_perform_update_hook(int img_index, struct image_header *img_head, const struct...
Hello,
In the nRF52840 Product Specification PDF v1.11, on page 836, the second paragraph down states:
" The PSEL.RXD, PSEL.CTS, PSEL.RTS, and PSEL.TXD registers and...
Hello Nordic team,
I’m using the nPM1300 development board to charge a 950 mAh Li-ion battery , and I’ve configured the charger as follows:
Charge current: 800 mA...
Hi,
I'm unable to get the PPKII kit to "connect" to my PC. After selecting the device it just says "Connecting..." forever. Some notes: - When first connecting the kit...
Hello,
I am trying to write a python script that performs a DFU on a nRF52840 so I can change its firmware without pressing any button. I think I have to use the pyusb...
Hello everyone,
I’m currently planning to develop an application that involves multiple Bluetooth devices operating within a certain range outdoors. Since there’s no option...
I’m developing an ESB-TX program using NCS v3.1.1 . Previously, I had developed an ESB-RX program using nRF SDK 17.0.2 . Now, when I use the TX code from the NCS SDK to communicate...
