The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
For power optimization I did to disable Mesh Using this piece of Code
and Re- Enable using this code
So the Real Question is that , After disabling Mesh for some time...
Hi
I need a suggestion. We are like to try a long-distance I2C communication between the sensor & Nrf5340 that is we need to connect 1.5 meters of cable between them. So...
The device advertises.
The phone scans.
The device use white listing and only allow one peer, the phone.
What's the difference between erasing bonds and disabling white...
Hi there,
I'm intending to use the nrfxlib modem library and its BSD socket implementation on the nRF9160. My goal is to use non-blocking APIs and use `nrf_poll` in response...
Hi,
I followed the DFU to SDK example post on https://www.u-blox.com/en/docs/UBX-19050198 to add Buttonless DFU to an application (I modified \ble_peripheral\ble_app_hrs...
Hi,
I'm using nRF Connect SDK v1.7.0 to develop a firmware for a custom board with a nRF52832 MCU. I'm using VSCode to build and flash my device using the nRF Extension...
Hi All,
My dev environment is as follow:
nRF52832(Central) + S132 + SES + SDK 17.0.2
Normally my Multilink Central code is flashing and working properly without...
I'd like to know of an example(s) for interfacing nRF52840DK board as a Master SPI to an Arduino badge (from Honeywell). I have the badge working with an Arduino Uno (Rev...
Hi,
If I want to use the NRF52833 as TX, and NRF24LE1 as receiver. How I can I match out the address?
If NRf24le1,
RX_addr = {0x00, 0x 11, 0x 22, 0x 33, 0x 44}
then...
Hello,
I'm working with NCS 1.7.1 and the nrf52840 dev kit to implement a BLE peripheral with FOTA, stats and configuration features. I've added MCUMGR to the project so...
Hi Sir,
As we know the inductor connected to the DCCH pin is a DCDC function for high voltage mode.
But what side effect we can see if we connected the inductor at the...
Hi,
I'm using NRF52840 to connect to an Android mobile phone.
The application scans for advertisement and when the NRF device starts advertising - connection is established...
Hi,
I'm evaluating the performance of the Zigbee protocol implementation on the nRF connect SDK using nRF52840dk:s. nRF connect SDK 1.7.0, ZBOSS I'm not sure where to find...
Hi everyone,
We are using the secure bootloader in our board, and we are adapting that bootloader for our requirements. Moreover, we use the DFU updates for our Main application...
