Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
I'm working on a custom board with a nRF52840 and a Micron NOR Flash MT25QU128ABA8E12-0SIT ( https://www.micron.com/products/nor-flash/serial-nor-flash/part-catalog/mt25qu128aba8e12...
Hello,
I use BroadVoice32OpenSource.v1.2.zip to test encoding and decoding,On windows10 or 52840，
using 16bit 16Khz Continuous audio，And has been converted bin2c array...
Hello All,
I am developing an nRF52840 MCU base thread product.
For this I am using nRF52840-Dev_kit for Development and SDK - nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b...
Hello!
We have a new board design we are working on that uses the new nRF5340 chip, revision Engineering A.
However, we are having difficulty getting the SPIM4 (High-Speed...
Hi All,
I'm a little rusty on my embedded C and was wondering if I could get a few broad pointers on the best way to organize this research system I'm putting together...
Dear Nordic:
I have a STM32 family MCU with a preloaded bootloader, to which I can update the firmware via UART. The goal I want to achieve is the following:
I want to...
Dear all,
We are using nrf52832 as our main MCU. In our development we need two uart. Among them first is Hardware uart which is working perfectly and second is software...
I am using the Arduino Nano 33 BLE Sense (with nRF52840) which comes with a mounted MEMS PDM microphone ( MP34DT05 ). My project will be battery powered and thus calls for...
I have successfully implemented the Azure IoT Hub sample on my nRF9160DK and added the ble scanning module. The kit is acting as a gateway, reading advertisements from a couple...
Hi ,
Device :- nrf52840
USB class :- CDC ACM
We are sending the ADC data (240 bytes at a time) to Host computer over USB (Full speed) and checking the received data...
Hi,
Using the Nordic secure bootloader for dfu OTA update, I am facing an issue causing the system to go under a condition where the bootloader is not any longer able to...
Hi. I'm trying to output frequency ( in the 1,250 Hz to 1,750 Hz range ) on GPIO. Each frequency should be outputted for 5ms time. For that, I use 2 TIMERs: one for 5ms counter...
Hi, we use nRF9160 and SDK 1.7.
in one of our applications, we need more than actually available flash. Now we have ~420kB for application - because we use MCUBoot and dual...
As title says, I cannot get anything to change in autoconf.h after changing the corresponding value in prj.conf using nRF Connect samples. I have tried both Project-->Reload...
I have made custom mobile app and I am trying to connect to it. When using nrf Connect app it is connecting properly
but i want to connect to my mobile app . it is connecting...
