the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi guys,
I am using nRF5 SDK for Mesh v4.2.0 and I implemented this simple message model which can enable the communication between LPN and server node. After my nodes are...
Hi everyone, I see in nRF5 SDK 16.0.0, a Button/Led/Timer assign for handler, like that: bsp_init(BSP_INIT_LEDS | BSP_INIT_BUTTONS, bsp_event_handler); Or: app_timer_create...
Hello,
I was working on buttonless dfu feature. I add buttonless dfu service as shown as ble_app_buttonless_dfu example and i manage to perform a ota dfu on nrf52 devkit...
Dear Sir.
Moving to version 2.4.99 from version 1.2.0 .
In previous version SPI worked well , cs was configured in overlay as
&spi3 { status = "okay"; compatible...
Hi,
I was evaluating FOTA on nRF5340 as possible upgrade to 52 series. All went good which I'm happy of.
However application size is limited roughly to half flash size...
Dear Community;
We are trying to send data via Lora using a nRF9160. The Lora transreceiver we are using is a RFM95W(Semtech SX1272). There are samples of code to receive...
Hi all,
I'm trying to set up my nRF52840 Dongle as a BLE Sniffer. I've followed the setup instructions from "nRF Sniffer for Bluetooth LE-- User Guide" v3.2, and I'm using...
Hi DevZone Team,
Is there a way to stop the ZigBee network steering after a device has successfully joined instead of waiting for the timeout to expire?
Thanks
Which nrf5340 BLE examples build and run? I've tried several and get build errors on everything I've tried.
This is for both the app and net processor.
Hi there,
I'm using nrf52840 DK and Custom board, SDK 17.0.2, Segger Embedded Studio(SES v5.20
my problem was the code running fine but after a while it will go...
Hi,
I am using w25q16 serial flash spi memory with nrf52832.
the flash memory is working fine with all analog input pins(2,3,4,5,28,29,30,31).
but due to the hardware...
sdk version:nrf5_SDK_for_Mesh_v5.0.0_src
in example/light_switch
I use the ios nrf mesh app as a provisioner and at the network layer
I can scan and find nrf5x...
SDK 14.2, NRF52840, S140
Hi,
Thank you so much in advance for answering my very long question. I am a little confused by the low power pwm example and app_PWM documentation...
