Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hi. I have attempted to add an out endpoint to the HID usb generic example (only 1 in endpoint in example as it is a mouse).
However it is not working. When connected my...
Is there any UART examples by directly accessing the registers?
Based on SDK15.0.2, for NRF52832 or NRF52810, higher freedom, higher memory utilization.
Hi, I measure current in beacon in Long Range mode. Behind 3 current peaks witch represent TX on channel CH37 CH38 CH39 there is a strange current peak, witch I don't understand...
Hi,
I can't build any samples anymore for my nrf9160-DK using neither SES nor CLI only.
I followed the "Getting started assistant", pulled the v0.4.0 version of the SDK...
We have successfully implemented & tested the working of SYSTEM ON SLEEP MODE feature in our nrf52840 devices.
Please reply to below queries for a similar issue:
Will...
hi, i've been trying to use uart in non-blocking mode (events available). Configuretion is the following: i have specify RX buffer (128 bytes) in init function, and in order...
Hi,
I would like to run the radio_test example on an nRF52811 chip for certification purposes.
What changes are required on the latest sample code and project to get it...
Hi all,
Is there any example to discover the custom UUID services with pc-ble-driver c/c++? As far as I understood, the ble_db_discovery is not supported for this driver...
Hi,
i am trying to Set TX power level from application using radio_modulated_tx_carrier() function from radio tool code. But when trying to run the code, application is...
Hello,
I am attempting to set up NVS to capture GPS data received from the modem for transmission to NB-IoT after collection has ended.
I have successfully implimented...
Hi everyone,
I m trying to communicate nRF52832 to an android application " nRF52 UART 2.0" on 9.0.
"nRF52 UART 2.0" app source is from git( https://github.com/NordicPlayground...
Hi everyone, I need to send data (coming from many sensors) from a nRF52 to PC via Bluetooth. I have a custom board with nRF52832 and I am using the nRF52 Development Kit...
Hi Team. There is a connection between nrf52840 and esp32-wroom over uart. Uart settings: baud rate - 115200, data - 8bit, HWFC - disable, Parity - excluded, stop bit - 0...
Hi. We have a project we would like to move to an nRF52840 SoC. I have modified the hid generic example to connect with our test software which basically can send and receive...
