Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
Hello,
i'm trying to use ble_advertising_init to initialize my advertising data, but when i use this function like it is used in the examples i get NRF_ERROR_INVALID_PARAM...
When I open device just after I plug it in the PC it work fine, but when I try to do it again (exit python script and run it again) I'm getting Error code 13.
Firmware:...
We are currently in the prototype stage using the nRF9160 and are preparing the firmware for the prototype. We have a few question that we hope someone could answer :)
Will...
Hi,
I want to test BLE 5.0 using two nRF52 dev kit. i am using the ble_app_uart example kindly guide me what are the changes to made in this example to connect two kits...
It's easy for me to create make file target but I am not able to identify where and how to add the custom target in the Segger Embedded Studio(SES).
My default build configuration...
Hi everyone. I am trying to find the best way to establish a Bluetooth connection to a nRF52832 in the least amount of time.
I'm designing an ultra low power perpheral...
Hello,
Would it be possible to create a partial code that can be placed on external memory, and loaded into ram for execution when needed?
As I believe it is possible...
Hi,
I am developing a Bluetooth peripheral application using NRF52832 MCU , where in it is used for collecting vibration sensor data for about specific duration.
like...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hello All,
I am new to Nordic and i have nRF52840 development kit. I want to build code/ programm on thread and Zigbee base.
I have downloaded the Thread and Zigbee SDK...
Hi!
I do not know what the problem is.
First of all, I use nrf52-dk and SDK 15.2
And then, i read 'PPK User Guide v2.3'
I use 'nRF Connect > Power Profiler' to measure...
Hi,
I use the SAADC with the NRF52832.
This is the schematic used :
When we use AN_IN (TOR_IN 1 and TOR_IN 2 are not used), only the components assigned to AN_IN are...
File nrf_pwr_mgmt.h is lacking
#ifdef __cplusplus extern "C" { #endif
magic.
SDK version: nRF5_SDK_15.3.0_59ac345.zip
I guess it is a small oversight since all other...
Hi using nrf52 SDK 15.1, on custom boards
I have certain flash operations using FDS. I have peer manager as well.
I am writing 8 byte data & later in the code updating...
