Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hi!
I am trying to use the SAADC driver on SDK13, following some examples from the playground repo. I am using the app timer to trigger a measurement for 4 channels. ...
Hello,
I cant seem to find a PBKDF2 function in the SDK to generate a private key from a passphrase.
We want to use mbed-tls or CC310 to make a SHA512 based key for AES...
Hi Everyone,
I have a custom board with nRF52840 and am testing out basic GPIO functionalities with some LEDs. In the board, the LED cathode is connected to nRF52840 GPIO...
Using nRF Connect for PC Version 2.6.1
Connect to a peripheral device that ask for an ATT_MTU > 247 bytes
NRF Connect fails with
Failed to call gattsExchangeMtuReply...
Hi
I have implemented (heavily base on the found examples) an application which uses both ESB and BLE. For now I focus on developing the ESB part of the SW. I am using the...
Hi Sir,
According to the nRF52832_PS_v1.4.pdf, In section 17.1.1, the table shows the current consumption of Radio. What's difference w/ Iradio_tx0 and Is0? Why do we get...
Dear Nordic Team,
We are building a very low power wearable with the nRF52810, only powered by a small solar cell and a super-capacitor.
We would like to offer firmware...
Hey,
I am working on nRF52 DK boards. Suddenly PC is not detecting the one of my DK board, but the nrf53832 processor's LEDs are functioning as per the last program dumped...
I am trying to use multiple channels for beacon transmission.I want to hop to a different channel at an interval of 2 seconds.I have configured one device as a pan coordinator...
Hello,
I'm using following code to read two channels of SAADC. It works fine when device is not connected to BLE central device. As soon as it's connected, the saadc_callback...
Hello,
I want to use 2 thingy:52 board in which one will act as master and other as slave. If yes, how can we do it? please provide any example code. Thank you.
hi guys, I'm looking for understand how to send a simple signal using ble mesh between two nrf52840 boards.
The available example aren't so usefull in order to have the...
I need to store a data base into an area of the FLASH. I understand I need to use the pstorage capability. All the reference I found about it , are just part of the code where...
Hi, I bought Sparkfun nrf52832 breakout board and i am having issues with programming a board.
I downloaded Segger embedded studio and nRFGo Studio for uploading hex files...
Hi,
I have set a Mesh Client Node with two BLE services: Mesh Proxy Service and Nordic Uart Service.
The problem is that when I send a message to the Mesh Client from...
