Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hello,
I am looking into migrating DFU and Bootloader over BLE from SDK v15.0 to SDK v15.3. I have a few questions about the code changes which I was hoping I could get...
I was reading about Mesh DFU and noticed that when it happens, the receiving node will rebroadcast it to all devices within radio range. It seems like devices will pick up...
Hello all,
I am trying to adjust the current consumption of my device based on nrf51822 s130.
A have read the https://developer.apple.com/hardwaredrivers/BluetoothDesignGuidelines...
I wrote some user data to 3rd party nrf52840 boards flash using the command "nrfjprog --memwr 0x1001084 --val 0x33333333" , when I ran the program the data values was not...
Hello,
I want to test the mesh provisioning demo with the codes provided on the GitHub:
https://github.com/NordicPlayground/thingy52-mesh-provisioning-demo
I have encountered...
We are using an NRF52840. After initializing a UART that uses P0.06-TX and P0.07-RX the following function calls fail: sd_ble_gap_device_name_set() and nrf_sdh_enable_rquest...
I am playing with the TIMER peripheral and I am seeing that I must call the function "nrf_timer_event_clear" in order to get the TIMER interrupt to stop firing once a COMPARE_EVENT...
As shown in subject, I tried to register many BLE services, DIS, BAS, HTS, and Custom Service. Then nRF52832(and nrf52840 preview) has stopped by an error of NRF_ERROR_NO_MEM...
I am working in nrf52840 sleep mode and it is working perfectly in system_off() mode, but while trying to wakeup from sleep using timer the device is not waking up because...
I am configuring the SAADC for Single-ended mode which I would think is a simple/common task, but my output from the ADC is very jittery. It seems to jump between a good reading...
Hi!
SDK15, s132, SD6.0.0, nRF52832
I have nRF52832 in central mode and some bonded HID devices and another nRF52832 peripherial devices.
Now in the my central nRF52832...
I simulated the balun of nrf51822 accroding to the referenced design of nrf51822 on the official website. However,it showed the differential phase of the balun was not 180...
Hello team,
We are using CPU NRF52832/810. We have followed the THINGY hardware for BLE Antenna with Ceramic Chip. Due to our range requirement more than 100 meter, we wanted...
