I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hi, I am working on SDK 15.0 Multilink central and Multi peripheral
Soft device: 6.0.0
Segger IDE
Application overview :
When the central request to all peripherals...
Hi, I have seen in other topics here that it is not possible to control the server of the light switch example from the Android App, only the Generic On Off Model. But when...
I am working on RTLS project using nrf52832 SOC. In beacon mode i want to advertise temperature and battery strength . but i am not sure if what method should i use to measure...
Hi,
I am using nrf51822 in my project.So we are using keil5 u vision project and sdk 12.3 version so here the problem is i have imported the example program from the sdk...
The nRF52840 supports 2 Master/Slave instances.
Is it possible to configure the nRF52840 as a Master when connected to an I2C bus that has another Master present?
SDK 15.2, S132 6.1, nRF52832
I have a characteristics to write data to a peripheral, using variable length up to 507 bytes and authorization.
Writing to the peripheral...
I'm using nrf_fstorage_wrile() which work fine on most of the cases, except for len == 6 bytes. When I read back on the Flash, after successful write, I found that only 6...
Hi,
It‘s great thing that the nRF9160 DK can buy.
But there are few question need to be confirmed?
1, I saw the "Onging ceretifications" ( https://www.nordicsemi.com...
Hi,
I am using a nRF9160 with the LTE-M modem firmware. But I want to change it to the NB-IoT firmware. I have followed the instructions to install the dfu.
But when I...
Hi
I am looking at the file
\examples\light_switch\server\light_switch_server_nrf52840_xxAA_s140_6_1_0.emProject
and in there I see that there is the line
linker_section_placements_segments...
Hi,
We are planning to develop an IOT device using the nRF52840 which will communicate with a Hub device which will contain another nRF52840 chip, so we want to check the...
Hello,
I am compiling with encryption implemented for Bluetooth communications. Specifically with code taken from the ble_app_hrs_c example.
I am seeing this error:
...
Hi Sir
I am testing nRF52840 product with CMW500 BT5.0 testing script. But the testing is easily stop due to connection broken, especially for RX and long range testing...
I made an application based on ble_app_uart example using s130_nrf51_2.0.1_softdevice.hex and I have 2 boards:
- 1 nrf51DK
- 1 target board using nRF51822-QFAA H0 (version...
