Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hello,
Thank you for considering my inquiry! I am looking for an example project with the firmware to run a gateway through the PC, nRFconnect software, and a nRF52840...
Hi,
I'm developing an application with the following hardware and software design components:
- nrf52840 DK with attached sensor
- nrf52840 USB dongle attached to debian...
Hi, I have some issues with my eclipse setup, I have installed all packages and followed the tutorial ( https://devzone.nordicsemi.com/tutorials/b/getting-started/posts/development...
Hello,
I am working on bootloader on nRF24LE1, for which a protected region should be configured. Therefore, I need to change NUPP in infoPage.
So my question is, is there...
Hi.
I watched the examples and docs with the on-off model. I tried to run these examples and configure. I don't understand when I need to use a server model when client...
I am seeing some behavior in BLE advertisement mode , that I would like to get feedback from expert in this forum. I am using modified Keyboard HID example, using nrf51 BLE...
Hi,
I'm using nrf52DK and 12.3V SDK .
in keil i can able to go to the debug session but when i press run button it is not working.
what could be issue ???
I have enabled RX address 0 only, (value of RXADDRESSES field is 0x01)
But still I got a received package interupt where RXMATCH has a value of 0x07, indicating that I...
Tx Radiated spurious emissions (1-18GHz): should be able to force the radio into a continuous transmit mode on a specific channel. The device should be transmitting with as...
Hello,
the BT specification states the following:
Is this particular requirement to be taken care by Nordic's customer using the BTIC? i.e. LE PHY qualification test...
Hi,
I want to use bsp_event_handler in SDK v11.0.0 . But the code is not getting compiled.
On building, it throws an error "error:#20: identifier "BSP_BUTTON_ACTION_RELEASE...
Hi,
I'm using NRF_LOG to print information via RTT backend (RTT viewer v6.20) and it has been working so far. After adding a single call to a function that reads 128 bytes...
I use one motor to drive one object move back and forth in a straight line, with two hall ic(XC3202) at the boundary points at both ends. The motor turn when the object reaches...
I'm using a central (Adafruit Bluefruit Feather nrf52) and peripheral (Adafruit Bluefruit 32u4) device for BLE communication. Peripheral is acting as remote, to turn on relays...
