Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hi,
I have implemented to the Master serial DFU. I able to send .dat file and i'm reading correct CRC .
I'm sending .bin 4096bytes and making 64bytes in a each packet...
Bluetooth Mesh specification uses the concept of composite models that "extend" other models. I am having trouble understanding the scope of this concept within the Mesh specification...
For nRF52840 (Rigado BMD-340), SDK 15.0.0, custom board:
I'm trying to implement nrfx_uart directly to communicate to another microcontroller. I've configured it for blocking...
Hi all
I'm using the NFCT peripheral of the nRF52832 Revision 1 and I'm facing the following issue:
When the reader sends the SLP_REQ, the NFCT receives an incomplete...
Hi, there
I want to remove the bond in current time service example, because the bond process make me less convenient when I debug. so I changed the code in peer_manager_init...
Hi using dev kit pca10040 and sdk 14.2.
I'm trying to use the dev kit buttons to stub out an ANT+ bike speed sensor. Essentially I just need a way to provide a speed reading...
Hello, i am using ble_app_uart example. i am trying to send A to Z from ble to uart. Has i noticed, it is transferring 20 characters at a time. to make sure that i add print...
I am using nRF5_SDK_15.2.0_9412b96. I have application data that accumulate in flash but can be thrown away before re-flashing new app image. I am thinking about instead of...
Hi,
I configured nrf_ble_qwr to use 256 byte long buffer in my BLE peripheral. I registered my value handles (2) which I want to support long writes using nrf_ble_qwr_attr_register...
Hi Folks,
I'm new at using the nRF52832 chip. I recently was handed a 3rd party board to evaluate and up until today I was able to use the nRF52 Development Kit to act...
Hi,
I am working on "nRf52832 - PC10040" based ISP1507/. I have already adapted the peripheral/spi example of SDK 15.0.0 to my needs. Now, I want to merge this spi example...
Hello,
With Segger ES I am able to compile and run the Blinky example (pca10040, S132) from the nRF5 SDK without any issues, it loads on my nRF52 DK board on and it shows...
Hi,
I'm working on a project where I need to collect and process analog data coming from high speed sensor measurements. The data needs to be read at a speed of 25k samples...
Hi,
I am trying to convert the string from ctime to a struct but i always get garbage values if i use "uint8_t". But i can get correct values if i use "int" datatype....
