I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello All,
Confirm the chip set replacement for the NRF51822 with NRF51802?
Can anyone suggest me which one is better with reference technical features.
Thanks
I used nrf52832 sdk14.2 development, modified on the basis of the ble_app_template project, and ported some of the user code previously in sdk12.3 to sdk14.2. After I open...
Hi
Over the last years working with Nordic I struggled from time to time over the disconnect reason 0x3E (BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED) on our devices with Central...
hii...
i have programmed the ble_uart with twi sensor ...
complied very successfully
but while i am debugging i am getting error in void twi_init()
why and also fatal...
Hi,
Here I met a problem, please help.
I am using proxy.c to establish an data link with smartphone via mesh_GATT.
What I am doing is like this:
For TX ,
it is...
IDE: keil uvision 5.23, SoftDevice 3.0.0, SDK 12.1
Computer Platform: Windows 10
Receiving device: nrf52832_xxAA
In our project, there is a sender always advertising...
Hi,
I have a project where, I need to change the minimum and maximum (MIN_CONN_INTERVAL and MAX_CONN_INTERVAL) connection interval to higher values like 1 second and 2 second...
hi everyone!
I am developing NRF52840 with the Development Kit.
I am trying to use a GPIO to o capture a external HIGH-TO-LOW signal and then trigger a LED.
I I learned...
Hi all,
I'm currently using nRF Connect in combination with a nRF52 DK to connect to my Mesh network. So right now I have to type all my commands as HEX messages and decode...
Hello,
I'm trying to compile the Light_switch_provisioner example (Debug, Mesh 2.2.0) in Segger Embedded studio.
<t: 0>, main.c, 561, ----- BLE Mesh Light Switch Provisioner...
hello
i wanted to send message using the simple message model with some modifications from client to server periodically but didn't know from where i should start , i tried...
Hi,
I'm working with the nrf52840-DK and using the nRF5 SDK v15.2.0 Stack version.
I´ve got a working program for my coordinator (C) and my end device (ED). The C establishes...
hello dear, is there any pre defined function or library in segger embedded studio for I2C interface..? i want to make communication with digital temperature sensor(MCP9808...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Hello.
I need to solve this problem urgently.
I have now created my own protocol and are testing.
At the point of this project is the guarantee of data transmission...
