I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
hi,
My custom board running Mesh SDK0.92 send and receive messages are normal.But after I replaced the MeshSDK in my program with Mesh SDK1.0.0, I was unable to send and...
Hello all,
I would like to establish connection between single central and two peripherals for bidirectional communication. I edited ble_multilink_central example and created...
I and new to programming the BLE devices and have just started out on the nRF52840 PDK and using Segger Embedded Studio for ARM v3.34. I have compiled and downloaded the ble_app_template...
I have to question:
1: if customer use relay node for mesh net, how much is the power consumption for one node? is there any passable to declare the power consumption to...
Hi,
I need to measure the capacitance of few capacitors for which I am currently using 3-channel CAP1203 IC from microchip.
However, I just came across the possibility of...
Hello,
I would like to establish bidirectional communication between single central and two peripherals. I referred ble multilink central example and made corresponding changes...
SDK： nRF5_SDK_11.0.0
Softdevice： s132_nrf52_2.0.0_softdevice
I set the WDT timeout in the application is 5s, when entering the BootLoader set the WDT time is 10s, how...
I am new to ble programming.
I am trying to find the best way to send json objects from android app to nrf52 chip.
What is the best way to send the json object to the...
Hello Sir,
I have developed small and compact product using nRF52832 Soc. Due to size limitation and device is portable. I have attached snap shot of power supply circuit...
Hello sir,
I am develop us product using nRF52832 chip on DK board use S132 soft device and its working well fine. So now we are designing hardware PCB of my product for...
Hello, I am trying to use adc with the uart so i can monitor the readings from adc. But when I include both drivers (nrf_drv_saadc , nrf_drv_uart) i got a confliction error...
Hello, although i have included every library and c file that is needed. i still get a declaration error. I'm almost sure that i enabled everything in sdk_config . I'm kinda...
In sd_power_system_off()，the nrf51822-board current is 2uA；And I think the current in sd_app_evt_wait() will be ~4uA(Is it correct)?
In sd_app_evt_wait(), the code...
In this example project
nRF5_SDK_12.3.0_d7731ad\examples\ble_central_and_peripheral\experimental\ble_app_multirole_lesc\main.c
/**@brief Function for initializing...
