Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
We want to receive the data in laptop over the BLE like nRF UART mobile APP.
we sending and receiving data in Mobile app but we can't get the app for desktop.
we...
Hi,
1-I did some test for nrf51422 (SDK12.3 + soft device S130) power consumption. result as below:
-system on sleep mode( without UART and BLE Advertise ):90uA
-system...
I am working on developing BLE app using connection oriented channel . I am using nordic semiconductor as a peripheral device and iPhone 6 as central manager.
I am able...
Hi,
I am working on a project that requires extremely low power consumption (20-50 uA) at max. We are currently consuming around 5.5mA. The project uses SPI to communicate...
Dear Nordic Team,
Thanks for supporting.
Currently i am try to check mesh network. I want mesh example code using keil IDE. I am using SDK12.3.0 and Hardware is nRF52...
How can i calculate the average current consumption, so i can estimate battery life.
This application uses Gazell to send data.
Peripherals used:
-UART for logging ...
Hi
I would like to connect the nRF52810 to 2 devices via UART interface by switching the Rx and TX GPIO pins by the software in realtime.
Is it possible? what is the method...
Hii
I m using Fanstel Ev board (BT840F) using nRF5248 Fimware.
i want to set maximum transmission power +8dbm in FANSTEL Ev Board but i got an error code 7 is Indicate...
Hi,guys.
In my experiment, Firstly,I creat an app_timer work every 20ms interval
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_OP_QUEUE_SIZE, false); err_code = app_timer_create...
Hi everyone,
Recently, I used the nrf52832 learning board to learn SDK13.0.0, when I see SAADC, tell the truth, this exampe is a bit difficult for me to understand.
My...
Hi
I am trying (for the first time) to deal with flash. Hence, I started by a simple app, without BLE/SD (blinker)
The problem is that, the first API call pstorage_init...
1. Connected to nRFgo Motherboard's nRF ISP and NRF24LE1E SPI pin
[nRF ISP]
[NRF24LE1E의 SPI]
2. In nRFgo Studio, Features> 2.4 GHz is disabled
3. I want to know...
Hi everyone!
My question is for engineers of Nordic. I need to apply NRF52840 as a " beacon ". As there is no ready templates of beacons in nRF5_SDK_13.0.0-1alpha_055eef3...
How to select nrf528332 UART clock source, how to make the serial port baud rate not change with temperature?When the baud rate is 9,600, the baud rate varies greatly with...
