I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello,
I'm trying to set up an app that enables the command line interface (CLI) over UART as well as the logging.
This is the what the main looks like:
int main...
I have set up the peripheral to transmit some dummy data, device information service, battery service and HTS service. I am getting started with the "central" now. Can some...
Hi，
First,i want to develop my project via SDK12.3 hrs project. I download the SD and app in hrs project in SDK12.3 via Keil ,but it does not work. I enter debug mode and...
Hi,
as far as I see, I can enable or disable external interrupts using NVIC_EnableIRQ() and NVIC_DisableIRQ . Is there a method to check if a specified external interrupt...
Hi everyone , I am trying connect two NRF52832 board over Bluetooth then display on Terminal over UART . Pls , give me an example for this problem .
Regard.
I would like to update ble device name from device1 to user2.
How i can do this in swift language . i m atrung to update by ios app.
is below way is right? but not able...
Hi Nordic,
I was reading the Wiki page for porting OpenThread to a new hardware platform ( github.com/.../Porting-Guide) and I noticed there isn't a "flash.h" header file...
MIN_CONN_INTERVAL
MAX_CONN_INTERVAL
SLAVE_LATENCY
CONN_SUP_TIMEOUT
Hey guys,
I want use my device with Android as well as iOS, but i am facing some issues for...
Hello, when reading the source code for a mesh node provisionee, I stumbled upon this MACRO function:
NRF_MESH_ASSERT
Edit: it is in ble_mesh_v0.9.1-Alpha\mesh\src...
hello,
i am experiencing issues with the TWI library on the smart beacon kit rev. 1.3.0 which features the v3 of the nRF51822. i had the same experience on the new nRF52840...
Hi. I'm trying to flash Secure DFU bootloader together with my application. I tried to flash bootloader and then main application, but the device stays in bootloader instead...
ppi.zip Hi, I am using radio with ppi to advertize packets as shown in the mainc file attached. Even after allocating the access address of Bluetooth on line 196 as set_address0...
Hi there,
I am trying to measure environment below 0 C but the app reboots and refuse to connect with thingy52 at lower temperatures. Do I have to set up anything else...
hi ,
I have a question about rtc.In my project ,I use rtc1 for app timer and rct0 for low_power_pwm.The problem is that I dont't have any idear to enable rtc0 instead of...
hello:
i meet some trouble,i can find the service,then appear error "BLE_GATT_STATUS:10a".
#define BLE_GATT_STATUS_ATTERR_ATTRIBUTE_NOT_FOUND 0x010A /**< ATT Error: Used...
