I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hello,
I want to know what is the correct way to use GPIOTE while my softdevice is running.
I have referred the example of pin_change_interrupt that is provided with SDK12...
I am trying to start scanning for devices.
I have changed from the example (ble_app_mulitlink_central_s130_pca10028) only
clock source to NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM...
Hi,
I want to know that how if we have Beacon on one side and Development kit on another side so it is possible to communicate them if they are using different services...
I'm using nRF SDK and trying to write firmware to my prototype device. However, nRF SDK doesn't detect my prototype device. I checked the power supply to my prototype device...
Hi,
I am testing example from sdk, 12.2.0, ble_app_uart, nrf52832
And i frequently get a strange behaviour where i don't get a response. And the connection is terminated...
Hello,
I'm trying to set my device on DFU mode by an android mobile application without success.
I'm working with nrf51822, sdk10, softdevice 8.0.
I subcribe to the...
Hi.
I'm using PCA10028, SDK12.2.0, S130 as central.
As I know "sd_ble_gap_tx_power_set" function let me set Advertising Tx power.
How can I set Tx power if i want to...
Hello,
I am going my project with NRG51822 in SDK 11. I build a android app that can connect to my device and access vendor specific service.
My device dedicates one...
Hi, All,
I'm testing multi-connection central function.
And I am struggled in getting relation of address.
AFSK, there are several types of address in BLE.
I found...
Hi.
I'm using nRF51822AC, SDK12.2.0, S130 as central.
After "sd_ble_gap_connect" function, how can I stop this function before connection?
I hope your reply.
Hello,
Is there a way to temporarily disable bonding and just allow any connection? I want to generally use bonding, but there are certain corner cases where I need to...
Hello,
I want to use the FDS libraries in order to store some data into nrf52's flash in my application and I have a bootloader to allow secure dfu by ble.
I manage...
I'm struggling with current consumption. I need my device to completely sleep and leave only the RTC on when the ext power is off (run on battery). After making sure my RTC...
Hy everyone!
I'm trying to write a non-volatile memory position of a device via I2C (twi), the device, a flash memory is the slave.
In my application, I have configure...
