Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Greetings starting from the 'ble aggregator' example I developed a BLE central on NRF52840 with NRF5 SDK 17.02, capable of managing multiple peripherals which, once connected...
I'm running SDK 2.8 and 2.8 Toolchain. I created the sysbuild.conf setting:
SB_CONFIG_BOOTLOADER_MCUBOOT=y
and put it in the application folder (per this support request...
Hello, I am relatively new to the nRF 5340 Audio DK. I recently ordered a singular nRF 5340 Audio DK board and my goal was for the board to take in input audio via the PDM...
Hi all,
I've been using the nRFConnect extension without any issues, successfully connecting to my nRF5340 board via JLink, flashing firmware, and receiving printed messages...
i get the following build error whenever i build for boards other than nrf
- CMake version: 3.21.0 -- Found Python3: C:/ncs/toolchains/b620d30767/opt/bin/python.exe (found...
Hello,
I encountered a compilation issue when using the app_timer function. The error message is: "'TickType_t' undeclared (first use in this function)". I believe the problem...
Hi,
I am trying to set the VDD pin to 3.0V instead of the current 1.8V (also changing the GPIO voltages to 3V). I've seen many questions related to that but no solution...
Hi Support Team
May we know that the difference between Engineering Build Code BB0 of nRF54L15 with normal Build Code? Which is recommended for the mass production of customer...
Hi, I am using nrf9151-DK to send and receive data over UDP protocol. Firstly, I tried to use AT commands to send and receive meassages as described here , I had no isuues...
Hi,
How can I control a Thread CoAP Client, which is connected to a thread supporting modem such as eero+ (in other words, the CoAP client is connected to the internet)...
Hello
I am trying to build the Zephyr mesh distributor sample on the nRF 52840 dongle
It builds and runs just find on the nRF52840 DK
But when I try to build for the...
Hello,
I'm looking at adding USB DFU to my project, (Not USB DFU recovery in the bootloader, but in runtime) and was trying this example. It fails to build for the nordic...
Hi,
im develop a keyboard by ncs sdk in nrf52840,and one funcation is that power off/on the keyboard ny fn key .i see the CAF: Power manager module , It doesn't seem to...
Hello, I've been developing on a Nrf5340 board and I am trying to gather pressure sensor data from both a adafruit mprls pressure sensor breakout board on i2c and then a Honeywell...
