hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem. ...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hi,
I am hoping to send/receive binary data (a protocol) on the same UART that has logging/shell enabled. Is there a way to access the UART RX traffic that the shell gets...
Hello DevZone,
I am using a nRF52840 with sdk 17.0.2 with Windows 10
I am trying to setup a connection to my Windows PC but I noticed data fragmentation and a queue...
I cannot get the nrf5340 audio dk kit to work from USB input properly. After a reset, it only works for a fraction of a second and audio stops. Has anyone run into a similar...
Hi,
I am working with the Matter Light Bulb sample . I have come across a problem where I can not compile my firmware if I implement the occupancy sensor cluster using the...
Hello! I have a GATT Server in the form of a nrf52840-DK that has been given to me from a company that has a custom service on the server using CCCD. I have the full documentation...
Hi,
In the NCS V2.3.0 version, I successfully obtained the serial device through the following code and compiled it But when I get the serial device in the same way in NCS...
I am having a recurring problem with NFC-CONNECT: build action. It hangs when building. Gets stuck with the following message in lower-right hand corner of screen:
The...
I want to use RTC in my project. I'm facing build issue (undefined reference to `__device_dts_ord_113') in my project .
STEPS TAKEN: 1. I have enabled the RTC configuration...
this is the last log message from monitor thread, I never got any error message from the thread.
00 > [ 01:37:03.890 , 808 ] <dbg> monitor: print_die_temperature: CPU...
Dear Nordic Team,
since the last release of NCS 2.7.0 the sd-card support breaks for me.
I am using the nrf5340 Audio DK with an inserted SD Card, and am running the zephyr...
Hello everyone.
I am going to do a project recently. We are using dht22 to transmit temperature and humidity, and use temperature values to control LEDs.
This project...
We have power ceilings configured as per the last nRF7002 Product Notice :
Yet we are seeing values below expected (around 13 dbm):
We noticed upgrading to 2.7.0...
Hello, and thanks for reading. We are having some problems with our device, and hope someone here has the missing piece of wisdom we need. Our device implements HID over GATT...
So in our factory I had setup both an nRF51-DK (PCA10028) and nRF52-DK (PCA10040) to program our external boards we are producing which has a NRF51822-QFAB-R7 populated on...
Hi,
My custom board uses Raytac MDBT53v, which has nRF5340 as its MCU.
My SW is based on the example audio code, and I want to use my external NOR FLAH IC (Macronix MX25R6435F...