I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
Hello,
I use Nrf52833DK running nRF Connect SDK (NCS)
I want read and write BLE MAC device address no matter it's the public one or static one.
Now i know bt_read_static_addr...
hello,
I'm try to fit my application to Android 14.
my application implement nordic DFU library ( for nrf52833 running freeRTOS firmware SDK 16 ) version 2.5.0
while...
Hi
I'm using the PDM module to capture audio through MP34DB02 PDM microphone ( here 's the datasheet). I set the clock frequency to default 1.032 MHz and a gain of +4 dB...
Hi there,
The nrf5340_audio application provides a -DFILE_ SUFFIX=fota overlay that adds FOTA capabilities to the application. This FOTA is introduced via Sysbuild configuration...
So I was experimenting with the Hardware Codec and I created a simple config which redirects the audio coming from the LINE IN mic to HEADPHONE OUT speakers.
Here's the...
We used the ADC nrf52832 to collect the reference source voltage, 1.240V. It is found that the consistency of each power-on is not good, for example, sometimes it is 2806...
Hi,
I'm running some transceiver tests to look at extended broadcast and ISO transfer modes. I am using nrf5340_audio_dk and ncs V2.6.0 to run nrf5340_audio application...
When testing the power consumption of the product with main IC 52832, we found that under the condition of 0dBm 1000ms, the peak current of beacon with PPK2 is about 15mA...
Hi, For the Adafruit Feather nRF52840 board I cannot find any information about the RTC. On the Feather board the 32kHz crystal is connected to the RTC clock input (P0.00...
Hi
I want to migrate my application to Zephyr RTOS platform from old setup given below.
Old Setup: Hardware: nRF52832 board. Soft device: S132 Software: SEGGER Embedded...
Hi, I'm new to Nordic Semiconductor chips.
I have experience programming STM32 and Atmel microprocessors. I would need to program/debug the NORDIC nRF52832 chip, without...
Hello there, I am working on enabling/ disabling DFU in nrf52840dk using ncs 2.4.2. previously i was doing it using ncs 1.8.0 as follows: libraries used:
#include <mgmt...
Hi,
I use the above function to create a new dataset. When I use SDK 2.3.0, this works perfectly. But when I use SDK 2.6.0 I get the following.
When I tried
arm-zephyr...
Hi all!
So I'm just starting out with the Thingy 91 and I was following the Nordic Thingy 91: Getting Starting Guide and I was in the process of using MCUBoot to update...
