nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hello,
I am deploying a thingy 91-x sensor outdoors to record acceleration data. I am reaching out requesting recommendations on what kind of solar panel would be able to...
Hello all,
I am trying to prove that I can compile and upload some simple code that I have written and run it successfully on an nrf52840.
I'm using an mdbt50q-db-40 development...
Dear Nordic Team, Does the nRF54L15's channel sounding function use the channel range of 79 channels (72 channels excluding the advertising channel) stated in the Bluetooth...
I just got my DK today and initially wrote the blink command to make the LED blink, which worked fine. Later, I wrote the AT command back, and the LED just keeps blinking...
I am developing a BLE mouse that can connect to 3 devices using nRF52840.
The sample code (peripheral_hids_mouse) allows simultaneous connection to multiple centrals....
Hello Team, We are currently building a circuit using nRF52840 CKAA (WLCSP -94) .We have configured P1.03 & P1.05 GPIO pins as UART_TX & RX . Kindly confirm if this pin or...
Hello, I am currently developing on the nRF54H20DK, which i have previously used v3.2.0-preview1 for. Everything works fine on v3.2.0-preview1. I have tried bumping to v3...
I am using the zephyr\samples\subsys\nvs example. By default the program stores data in internal flash in storage_partition. I would like to create a custom board file for...
I am using the peripheral_uart example. Now, our device tree seems to have crashed. Before the crash, I added the following configurations to prj.conf of the application core...
Hello,
I'm having some issues with the channel sounding on the nRF54L15. I'm using two nRF54L15-dk and two custom bords with the nRF54L15.I'm using SDK v3.0.2 for my software...
I’m trying to debug an existing product by opening its old firmware project on a new PC. The project uses nRF5 SDK for Mesh v2.1.1 , SoftDevice S132 , and nRF52832 .
I installed...
I am currently working in project with nrf54l15dk and 3.0.2 sdk. I'm trying to work with peripherals and I want my project to do the following: -Have 2 PWM outputs that used...
Hi DevZone Community
I'm trying to get a simple Hello World sample to run on an nRF5340DK board with a 2.8" ILI9341 based TFT display that has Arduino headers attached ...
Hello,
Im currently in the process of integrating Memfault OTA on the nRF9151 DK. My project has multiple boards: nRF9151 DK connects with nRF52840 DK via UART for communication...
