I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
Is it possible to build an asset tracker on the nRF91 without the use of LTE-M or NB-IoT? If there is a solution, could someone please advise. I read something about GNSS...
Hello,
SDK : nRF5_SDK_17.1.0_ddde560
Example: ble_app_uart
I want to use custom peripheral and disable BSP.
but when comment buttons_leds_init(&erase_bonds);
I...
I'm using nRF Connect SDK with nRF52840dk and going through the UART samples and currently have both the P olling and Async methods working to some extent. But questions for...
Triggering advertising by button pressed. But when advertising state is not idle. Both sd_ble_gap_adv_set_configure() and ble_advertising_start() failed with errCode 0x8....
Hi,
I am developing the nRF52833 DK with NCS v2.00.
I am using a function in my source code that reads the current RSSI of the connection. The function, read_conn_rssi...
Hi there,
I am trying to implement the OTA DFU feature via Zigbee in my product. i tried to implement the example available in SDK as below https://infocenter.nordicsemi...
We are able to build nrf5340_audio application with SBC codec,
but error occurs when program the app core with buildprog.py
dongtaotao@dongtaotao-OptiPlex-5070:~/ncs_v2...
Hi,
We setup a mesh network with 26 sensor devices, configured these 26 devices into one group. From the mesh gateway device, it sends group message to these 26 devices...
Greetings,
In our product, we encountered an issue when data saved in flash (FDS) that were previously retained are erased during DFU on some devices . This was indeed fixed...
Hi, I'm building an applicaiton based on ble_app_uart. I got that using idle_state_handle(); function to set the my nRF52833 into system ON mode. I disable system OFF mode...
Hi,
I am developing the nRF52833 DK with NCS 2.00.
I have successfully implemented a service to print the RSSI on the Android nRF Connect application. I use the function...
Hi all.
What is the best practice to set the system in standby? I have a PWM and when is active the system can be in a low power consumption until a button is pressed. But...
Hi,
I've some questions on nPM1100's buck regulator
1) What is the Iq (quiescent current)?
2) Does it support 100% duty cycle?
3) What will happen to VOUTB if VINT...
