nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hello Everyone,
I was use Nordic App for Mesh in android to add Telink's chipset into mesh. But after few minutes, telink's device go out Mesh.
I don't know how to add...
Hi,
Iam using "pca10056_s140_ble" secure bootloader example for my project.
FYI. My project gets its new firmware from internet and stores it in BANK1 memory using GSM...
hi Support team,
customer get samples with 9160, but find out they are not able get pin code.
i searched the spec, and at command +CPIN, it is not able to read out the...
Hi,
I've installed ncs manually following this guide: Installing manually — nRF Connect SDK 2.0.99 documentation (nordicsemi.com) and then set the following environment...
Hi,
I have an application using MCUboot (Only for using with serial recovery. No SMP server running in app).
I enable CONFIG_BOOTLOADER_MCUBOOT and parent and child images...
Hi,
I am using nRF5340 DK + NCS v2.0.0 with nrfx backend for SPIM.
For my application I want to trigger a SPIM1 transaction at a fixed interval. To do this, I set up an...
Hello,
I have an issue when trying to use NVS backend for BLE settings with the settings_storage partition in defined external flash region. As we are doing a multi-image...
I am designing a bluetooth module using the soft device S130 + nRF51822. I intend to refer to QDID80592 and 45222 when purchasing DID for bluetooth. When I checked the ICS...
Hi. I am trying to develop a project that use mqtt connection using nrf9160. Currently using thingy:91 for evalutation board. I am using Mobily Network on NB IoT at Saudi...
Dear Nordic Engineers,
When I plugged in and I opened the Power Profiler App, a pop up required me to update the device firmware.
During the FW upgrade the device flashed...
I am trying to use the DTM example for nRF5340 DK (PCA10095). The example is located at "C:\v1.7.0\nrf\samples\bluetooth\direct_test_mode", but I am facing "NRF_RADIO_Type...
Hello there. I am wondering, if while connection establishment or any other communication event through NFC and BLE the system addresses to NVMC? (Maybe mac address or some...
Hello
I search a way to have a similar project as pc-ble-driver with NRF connect sdk
There is a peripherial with many sensor that send data over BLE and i want to command...
Dear all,
When the provisioner add appkey or bind appkey for the node's model, I want to be informed and run a callback function.
Can I set callback for config server...
