Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
Hello,
In nRF5340 I use one RTC and it works. Here is my code:
1) in prj.conf:
CONFIG_NRFX_RTC=y CONFIG_NRFX_RTC0=y
2) in the code:
a) define: nrfx_rtc_t sti_period_rtc_0...
Good morning,
I am using the nRF9160 as an AT command modem running the SLM app. I aim to set eDRX and disable PSM (PSM doesn´t make sense in our project). According to...
Hi all,
My team and I are evaluating some BLE modules available on the market. One of them is the UBLOX BMD-340, which contains the nRF52840-QIAA SoC.
We are encountering...
Hello Nordic Engineer,
I have already implemented a Mesh network using iOS nRF Mesh, 5340 DK, and 52840 DK, with the mesh_light example.
The NUS I used before was able...
I am trying to flash the Enhanced ShockBurst (ESB) example on an nRF52840 USB Dongle (PCA10059) . Since the ESB example is originally designed for the PCA10056 (nRF52840 DK...
Hi all, need to establish a CIS connection to an already connected BLE device with security level > = 2 . However when the ACL connection has security level > = 2 and the...
Hi,
i have some code thats based off of the uart_async_adapter.c example code. I' m getting a `usage fault` which i've traced to uart_irq_handler. it happens when i try...
Hello, We're developing a project on a custom board based on nRF52832 and noticed that P0.20 is high on powerup, even with no firmware. Is there a way to controll the pin...
In the nRF5340 Audio DK example located at C:\ncs\nrf\applications\nrf5340_audio , I want to add a third board and communicate with it from the master (gateway) to send commands...
Hi,
We are considering hooking up an external chip with a Bluetooth standard HCI interface to do Bluetooth classic using Hands Free protocol and Serial Profile protocol...
How can I read the whole advertising packet when are packets larger than some specific size? This is the issue. I want to read this adv packet:
But I only get this on...
Hi,
We are facing a critical power consumption issue in our nRF52-based Zephyr application , where some devices randomly enter a high-power consumption state (~80+ µA) instead...
we have 6 custom board with nRF52840 we are able to flash test codes in 2 boards , while 4 boards give
Error :No Cortex-M SW Device Found . this is in nrf sdk .
when we...
Hi,
I am trying to set the Tx power level on the central device, I have followed the nordic example samples/bluetooth/hci_pwr_ctrl in the Zephyr tree. But it only sets for...
Hello,
I am new to Bluetooth. I have two nrf5340 LE Audio SDKs which I have been able to configure and use as gateway and headset (walkie talkie, USB, and line-in, CIS and...
