Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi there,
We are trying to enable the interrupts on one of the UARTE peripherals, and are having trouble finding the interrupt number within nrf5340_application.h? It is...
Hi Everyone,
The custom device I am working on is a BLE peripheral device and uses softdevice S132,
therefore to get accurate triggering of ADC sampling and to avoid periodic...
Dears,
We are MCU Programmer Supplier, now we are developing the off-Line Programmer for NRF5340, and encounter some problem as below:
1. Does the Nrf5340 Flash Memory...
I have a custom model server that sends 8 bytes of data
I set up 2 nodes - one to publish to an address 0xC002, one to subscribe to publication
Provisioning and publish...
Is there any documentation/tutorials for using NRFX drivers directly in Zephyr without trying to create conforming device drivers? I have a lot of code written for the NRF52840...
We have a board based on the nrf9160dk.
The project is essentially based off the "LTE sensor gateway" project with hcl_lpuart to utilize the nrf52840 for BLE. Chip shortages...
Hello,
I am performing garbage collection. During the garbage collection an event could be fired (from the softdevice) that causes updating of records.
My question is...
Hi
I would like to know, if Zephyr-s ssd16xx driver supports display driver board power supply control? I see from Zephyr documentation ( solomon,ssd16xxfb (on spi bus)...
Hello,
I recently installed the nRF Connect extension for VS Code on my Mac M1. I am unable to see my connected board as part of the nRF Connect extension.
Setup
...
Hi,
I see that the latest Nordic SDK ( v17.1.0) supports mbed TLS version of 2.16.10 only. However, we have received a End of life notification for the same ( Mbed TLS...
Dear All
Could you point me a timer example, can be used to time the interval in ms between something? like read the system time when something happens and then read again...
Is there a way to find you the reason for RRC Connect?
I'm using a simple software developed based on NCS AWS IoT sample. I've implemented the SW to test power consumption...
Hi,
I need to configure an nRF52832 to wake up periodically from SYSTEM_ON and SYSTEM_OFF and, also, when a GPIO pin changes.
Where can I find sample code and docs for...
Hi Nordic experts,
i figure out how to add the end-point-out to the BLE HID EXAMPLE and i cheched it out on linux ubuntu and on windows 10.
It seems to work correctly...
