Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
I am using the RSA sample code and I need to make the key persist. When I try to change the lifetime attribute to PSA_KEY_LIFETIME_PERSISTENT, the key generation fails...
Hi, I am developing a device using the nRF52832 mcu. I have written my application and have interfaced with an external I2C Sensor. It works perfectly on the NRF52-DK, I get...
I am using NCS v1.9.1 with the nRF52840 and I am not able to move the MCUBoot secondary slot to SPI flash.
I have been able to communicate with the device over the SPI...
Hello,
The nrfjprog command is used for the nrf51822 / nrf52833 program.
Suddenly, nrf52833 shows the following error.
Even though family is specified, it is the same...
Hi,
I'm working on NRF52840 DK , S140 and I'm trying to send large data (around ~64KBytes) from a peripheral device. I'm using the following functions: - sd_ble_gatts_hvx...
Hi Everyone,
I'm currently testing the battery service with my development kit, nrF52dk, and I've found an error stating "The handle is invalid" when I press the "read"...
Hi,
I want to build a wireless split keyboard (Left and right parts). I want them to connect to one PC but only need to establish the connection one time. Can both part...
I am working on ble mesh with sdk17.0 and sdk5 for mesh I want to send large data vai ble mesh I followed this post https://devzone.nordicsemi.com/f/nordic-q-a/71105/sending...
Hello.
I've a ublox module with nRF52811 chip.
Is it possible to make a BLE beacon receiver with nRF52811? If yes, is there any demo application? I've searched nRF SDK...
I have been playing with an Ikea Tradfri E1812 button, a Philips Hue bulb, and zigbee2mqtt. I see that when I bind the button's OnOff output cluster to the bulb's OnOff input...
Hello,
I am looking into evaluating the nrf5340 with different functions running out of external flash, and how current draw is affected by these functions. We are looking...
Hi All,
I am working on NRF52840 and trying to optimize the BLE throughput. The current settings are:
PHY: 2M PHY
Conncetion Interval: 9.375 ~ 15 ms
GAP_DATA_LENGTH...
Hi Everyone,
I hope you all are well.
I'm using nrf Connect SDK v1.7.0 and VS code for nrf52833 chipset.
So far I've used NUS service in my code to transmit some data...
Hi, I am trying to write an "event dispatcher" so it's possible to listen to types of event and send events. You pass a function pointer and it will be called when that event...
I was gone for a bit came back did my updates and I can't program my boards threw nRF connect anymore. They just don't show up so reinstalled everything many times restarted...
