Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
Hi am trying to use Nrf54l15 as a controller with an external host for the Channel sounding feature. I can receive CS subevents from the NRF controller, but the same thing...
I am using a QFN73 pin package of nRF52840. The data sheet says it has built in balun. So if I follow the reference circuit, where do I see 50 ohm looking int to the chip...
having just seen the announcment about the bare-metal SDK, i gave it a try using my "hello world" of BLE -- a minimal beacon app which i actually use to benchmark BLE platforms...
Hi
I am capturing a digital signal with the nRF PowerProfiler Kit II from my board that can either be 12Hz or 2kHz depending on the state of my application.
In the below...
I am using an nrf52833 with MCU boot. In an abnormal situation, the Vcc hoovers around the BOD threshold of 1.6V-1.7V. The Vcc in this situation is noisy (with 100/150mv swings...
Hi,
I have been making a sequential channel sounding program. I tried very hard to get rid of memory leaks and now the program is able to sequentially range with three reflectors...
Hi,
I am in progress of making own audio application. I wanted to try 8_2 configuration. I see however, that despite that, 10ms window worth of data at that sample rate...
Hello. Earlier we had nordicplayground/nrfconnect-sdk docker images for v2 (e.g. nordicplayground/nrfconnect-sdk:v2.9-branch ). But it seems there is no docker image such...
I have the revision 1.0.0 of the nRF54L15-DK. I want to use the SPI pins on the GPIO header P2. The datasheet says: nRF Connect for Desktop's Board Configurator application...
Hello,
After updating to the latest version of nRF Connect for VS Code, I encountered an error.
I am no longer able to erase, recover, or reset a board from within VS...
Hi,
we develop a battery powered device that has a battery charger ic. Can the ppk 2 measure negative currents in ampere mode when the battery is charged?
Hi all,
I have Nrf52 devices that use Nrf DFU with "Buttonless Secure DFU Service".
I would like to integrated the ability do to firmware update the devices to our "fleet...
For the nRF54L15, what is the voltage at the output pin of DCC (and input pins of DECD, DECA, and DECRF) in DC-DC mode?
Is it 0.9V? Is it constant?
Vinson
Hi,
We are using both nRF54L15 and nRF54L10 in our product, with DFU support where an external flash is used as the secondary partition on both MCUs. The hardware connections...
