Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
Hello,
I've been trying to figure why calling sd_ble_gap_tx_power_set() continues to return the error NRF_ERROR_NO_MEM. I'm using SDK 17.0.2 with S113, v7.2.0 on the NRF52840...
Hi team,
Currently am working on PWM example from SDK i.e. (Nordic SDK v1.8.0), am testing the pwm example from the sample i'e v (1.8.0\zephyr\samples\basic\blinky_pwm)...
I have nrf52840 pcb without XTAL 32768Hz. When I flash it with Zephyr sample project "Peripheral uart" it doesnt work.
How can I config project to work without XTAL on the...
The application seems to stop at an instance where I invoke a Send call to send data over to a ble central, and the callstack looks as follows. Any way to narrow down the...
I'm using Ant sdh,I want to make system enter sleep,how to disable nrf_sdh_ant?
I usd this function to enable sdh,but can't disable sdh to enter sleep,how to use?
static...
Hello,
1.Which platform is recommended for developing Bluetooth mesh, nrf5-sdk-for-mesh or NCS?
2.What is the difference between nrf5-sdk-for-mesh and NCS?
3.What is...
Hello Devzone Community,
I am facing a run time, peripheral or sensor initialization error in a Zephyr based app, built using sdk-nrf v1.6.1, and its corresponding Zephyr...
My Zephyr based application is buildable and working fine. I followed this tutorial, trying to enable bluetooth OTA for my app: Add DFU support to your application - Software...
SDK Environment: nRF Connect SDK v1.8.0 Target: Decawave DWM1001-DEV. This uses the nRF52832
I used \ncs\v1.8.0\bootloader\mcuboot\samples\zephyr\hello-world as a starting...
Hello,
We have a battery-powered product that currently uses the NRF52832. It is a very low power space-constrained application, so we always evaluate any potential current...
Hello,
I have set my softdevice s132v3 with SDK12.2 and nrf52832 to use connection event length extension and data length extende with connection parameters as shown below...
Two Factor Authentification is enabled for my primary account (I had to create a second one to ask question).
Something has gone wrong with setting up two factor authentification...
I wanted to implement a time sync feature on nRF-52840 DK. I took a reference from this example, but there were certain things unclear to me.
Can somebody explain to me...
Hello. I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
There is a numeric comparison as an authentication method, can I do it with sdk17.0...
Hello,
I'm new with Nordic products, and I'm trying to use my New dev kit nrf5340 DK.
The request today is about my code, I implemented my code in the DK, and now I want...
