nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi!
I managed to get the device connected to the nrfCloud and started receiving messages from it.
Anyway, the embedded antenna cannot catch the signal very strongly. Can...
Hi,
I am trying to test the asset tracker code on the nRF9160DK from the precompiled hex files from [ images_dfu_hex/nrf9160dk_asset_tracker_dfu_2020-04-29_bc7ade8b.hex...
It was my idea to compile the mqtt_simple vom v1.3.0.
I spend now one week with your sdk. I tried it with SES and also with command line. Absolutly nothing worked.
The...
I am using a nRF52840-PCA10059 dongle to acquire data at a high rate (between 50Hz and 400Hz).
The connection is very unstable, after some seconds of acquisition, it sort...
We recently bought four 'nRF 52840' dk boards, and are trying to do board to board (non-mesh but single) wireless connection. However, there are just documents of mesh-communication...
Hi all,
I'm running into trouble using openocd to flash code onto the nrf52840 and then step through it. I'm running High Sierra (although I doubt that's important), and...
Hi, I'm designing water meter modem using the nRF52840 + nRF9160. I will apply nRF52840 as a HOST CPU and the nRF160 contol by nRF52840. (please refer to picture.) Which Interface...
I have developed an app with DFU using SD s112(version 5) for custom NRF52810 board.
Q1: I want to update SD s112 to version 7. is it possible ?
Q2: how ?
Hello,
I'd like to detect a power failure and keep the nRF52840 alive using for example a super capacitor.
From the hardware side, is it ok to just feed the nRF52840 through...
I am a newbie for BLE MESH. Trying to migrate the existing product which based on self-defined GATT service to BLE MESH network, and got confused.
Current scenerio, the...
Hi.
I am using nRF52840 as a USB mass storage device with SD card. I came across the docs stating that the total number of BULK endpoints available are 14 (7 IN, 7 OUT)...
I have a working code to get FatFs running with SD card over SPI0 interface on a nRF52840 DK. I wanted to know if it is possible to add another SD card with FatFs on SPI2...
Hi,
With the S132 SoftDevice running, is there a way I can ask it to temporarily pause interrupts for a small segment of time so that I can execute extremely time critical...
Hi, The DFU process is working correctly and I've tried downgrading the app version which throws the expected error, so it is stored someplace Accessing via the recommended...
