Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
I have successfully completed my bachelor thesis project on a simple wireless sensor network using 3 nRF52 nodes and RPi with using Mqtt and Ble-6LoWPAN example from SDK....
Hi All,
We use nRF52 BLE Sniffer.Its working fiine. Please letus know, weather its possible to sniff multiple BLE devices at a time using single Sniffer. If possible, let...
Will there be an official implementation from nordic of the generic mesh models as described in the mesh model specification or are you counting on each developer to make...
How to change the Bluetooth Mesh broadcast address?
Use the sd_ble_gap_addr_set function to change the broadcast address of PB-GATT ， But PB-ADV still hasn't changed.
...
We are implementing a DFU controller in a microcontroller that communicates with the nRF boot-loader over serial. The target device is nRF52832 using SDKv15.3.0. The boot...
Hello.
I want to see NRF_LOG_DEBUG ("some") through the terminal. When I compile, I get the following error: What should I set or change? MCU : nRF52840 compiler: IAR...
1.I used Nrf52810 and the flash size is 192KB. I now need Master mode and slave mode. The SoftDevice I chose is S132 (S112 slave mode only). I found that S132 (130KB) + Bootloader...
Hi.
I have issue measure ADC value from battery.
setup is NRF52832, SDK 15.3.0, S332, using ANT+, BLE, GPIOTE, PPI, RTC, APPTIMER, LOW_PWM
my goal is measure periodically...
Hi all,
I am struggling measuring time between events. I thought to use the timer driver and the nrf_drv_timer_capture_get function. This is my test code:
I expected...
I am using nRF5_SDK_15.2.0_9412b96, softdevoce 6.1.1, NRF52840, based on ble_app_uart example.
I have a disconnection problem after couple of hours from an android app...
Hi everyone!
I'm using nrf52832 SDK version 15.0 and softdevice S132 V6.0.0. I'm getting an error when trying to program our board:
"Failed to connect to target.
No...
The build environment is a clean install of SEGGER Embedded Studio for ARM Release 3.50 Build 2018081000.36713 Windows x64
The nRF5_SDK_15.2.0_9412b96 version SDK is used...
Hello People,
I am new to this ble mesh concepts, i am evaluating and want to check whether nrf52-mesh-light-switch-client-server-proxy can supports custom service? if so...
Hello,
I just received my NRF52840-DK board today. I was able to run the demo (LED blink/Switch and NFC) which comes factory installed. But copying the hex files from demo...
Hello,
I am trying to migrate to nrfx drivers in my project. Currently using SDK15.2 and nrf52840. I have 2 SPI peripherals in my application. One being an SD card and the...
