Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello All,
Currently i am working on nrf51422 DK board(PCA10028). I am using SDK 12.3.0 ,from this i have referred the ble_app_uart example for implementing the UART and...
Hello,
After following the steps of the tutorial : https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/getting-started-with...
I have an application that works on nrf52832 that when it is powered on is expected to read a sensor data for initial 10 seconds if any, and then start BLE advertising for...
Hello Nordic Team,
I have an application where i am playing some samples over i2s to an audio amplifier. The application also uses fds to store those samples (they can be...
Hi Sir,
In the latest datasheet (52832_v1.4), our reference schematic shows the cap (C6) of DEC2 can be NC.
For DEC2, it is 1.3V regulator supply for Radio, may I know...
Hi
I am giving a try to ESB as an alternative to BLE. I am starting with esb_prx and esb_ptx sample.
That sample works on DK boards.
In order to save energy I would...
Hello to all,
I am using nRF52832 DK with sd132, v6.0.0 and sdk 15.0.0, segger embedded studio. We want to achieve change application timer time (APP_TIMER_TICKS(update_time...
I use nRF52810 and S112 as the soft device. And I use SDK 15.2.0. My BLE device works as a peripheral. And I have to connect some iOS and Android devices with bonding. Communications...
Hello,
I have a problem, I want to measure the power consumption of the nRF9160 with the nRF9160 DK, and I have the N6705B power analyzer, and I like to know how the connection...
Hello dear Nordic community,
We have developed a custom board that contains the nordic nrf52832, which is communicating via I2C bus with a 9-axis sensor (Bosch BMX055...
I am using Softdevice 140 with SDK v15.2 on Segger studio to develope a ble application. when Debugging, the program gets stuck as shown in the attached video. However, the...
Hi, everyone,
We are developing BlueTooth projects on NRF52832 and NRF51822 modules. The projects are built from DFU Bootloader, Soft Device and Main Application. Each one...
Hi Sir,
For EN 300 328 V2.1.1, I reference below setting.
https://devzone.nordicsemi.com/f/nordic-q-a/21643/en-300-328-v2-1-1-receiver-blocking-test-setup/84959#84959...
Hi
I am using TIMER3 and TIMER4 for generating PWM signals using PPI and synchronizing ADC sampling, respectively. I posted the preliminary project in here . After taking...
