Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i've got the TWI scanner example flashed onto the NRF51 dk board, using the default "Arduino" pins of P0.07 and P0.30 as SDA/SCL.
I've added two lines to the example...
I have a small collection of i2c devices on the bus that can be jumpered in (sda/scl disconnected). I am currently using SDK v10 and Keil v4.
I wrote this code to namely...
Hi,
I am trying to use the SSD1306 display with the nRF9160 DK.
I am using the code as is shown here
https://github.com/zephyrproject-rtos/zephyr/tree/master/samples...
hi, thanks for this tutorial : devzone.nordicsemi.com/.../ble-advertising-a-beginners-tutorial
i'm trying it on my nRF52840 devkit board.testing it with nRF connect application...
I have a nordic ble dongle. I want to interface it with an external microcontroller via usb. Is there a set of usb commands that can invoke the softdevice api's in nordic...
Hi,
I have a question about how IPv6 addressing works in an OpenThread network. I read in the OpenThread website that the ML-EID is also known a Unique Local Address (ULA...
Hi,
So I've made a post that I was unable to debug my app with the bootloader. But I've found out that it is entirely different problem. So my app is runnning whit FreeRTOS...
I'm trying to sample analog input but there is no value after sampling.
I tested the input by configuring it as digital input and it worked correctly.
Below is code. Any...
Hi,
I totally forgot about the voltage level difference between the debugger and the dongle and connected them. It was somehow working in some cases but not consistenly...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hi,
I want to log the application error data log into the internal flash(1MB) using the mesh example. I found that there are two ways of writing 1)FDS 2)Flash Manager. I...
hi ,
i am using nrf52832 dev kit , using which i am capturing accelerometer data from LIS3DSH for an RTC interrupt of 2 minutes, i.e., for every 2 minutes it should capture...
Hi
I have nRF52832 development kit and a few custom boards. I am planning to run some Mesh examples using the boards. But, almost all the examples require at least 2 Development...
We use nRF52832 (S112 / S130) and nRF840 (S140) for our future products
By default server device which supports BLE 4.2 shall fallback to BLE 4.0 and accept connection request...
