I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
Details: SDK v15.2.0 using peripheral spi example. Windows 8.1, uploading to nRF52 DK.
When I upload the example as is my clock , MOSI and select line work as expected ...
Our project is to read the gyro (lis3dh) by using SPI communication.
Since the infocenter says that using nrf52832 for developing nrf52810 is okay.
We currently developed...
I have a client that's investigating BLE solutions to use in a future product. The rough specs they gave me include a TX power of +10dBm. The nRF52840 looks like a good option...
Hi,
In the BLE_UART example, I am trying to get some data about the time delay between the sending and the receiving of data between central and peripheral devices.
I...
I've been struggling with this for quite a while now. I've got a PCA10040 to spare that I am trying to use with nrf sniffer in Wireshark. I'm using a new iMac with the latest...
I have a problem I'm using nrf52840 DK. The task i want perform is start from idle state, wait for a button signal and the go out from idle, start with a loop where the code...
Hello ?
I was surprised that the program was organically well organized.
Based on the given installation manual, I completed the installation and corrected the program...
Hi!
We are using NRF52832 and NRF52840 with custom rf protocol.
I didn't found any information about time for applying new TXPOWER value of radio module.
Can I start...
Based on mesh sdk 3.1, open NRF_LOG_ENABLED in the light_switch_server example, ie NRF_LOG_ENABLED 1, the following error occurred during compilation: Linking light_switch_server_nrf52840_xxAA_s140_6...
I had two nRF52832 where one broadcasts with encrypted data of advertising beacon info and another nRF52832 should only scan without connecting and should decrypt the data...
Hello,
We are using nRF52832xx_aa controller for our product, the sleep current consumption is approx 2 uA @25 degree Celsius which is fine with me. But when the temperature...
We are writing SPI drivers for RF chip and blocked on the below issue. The issue we are facing is the Chip Select line is not active(active low) until the TX transaction is...
SDK: 12.3.0
SOFTDEVICE: s130_nrf51_2.0.1_softdevice
CHIP: nrf51822 AC 256K flash 32K ram
GCC flags:
# C flags common to all targets
CFLAGS += -DBOARD_CUSTOM
CFLAGS...
Hi,
I want to write or change the code in to nRF52832
I have some code this code i should write for nRF52832
kindly give any suggestion
here is the my code
uint8_t...
