the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hi!
I am trying to use the SAADC driver on SDK13, following some examples from the playground repo. I am using the app timer to trigger a measurement for 4 channels. ...
Hello,
I cant seem to find a PBKDF2 function in the SDK to generate a private key from a passphrase.
We want to use mbed-tls or CC310 to make a SHA512 based key for AES...
Hi Everyone,
I have a custom board with nRF52840 and am testing out basic GPIO functionalities with some LEDs. In the board, the LED cathode is connected to nRF52840 GPIO...
Using nRF Connect for PC Version 2.6.1
Connect to a peripheral device that ask for an ATT_MTU > 247 bytes
NRF Connect fails with
Failed to call gattsExchangeMtuReply...
Hi
I have implemented (heavily base on the found examples) an application which uses both ESB and BLE. For now I focus on developing the ESB part of the SW. I am using the...
Hi Sir,
According to the nRF52832_PS_v1.4.pdf, In section 17.1.1, the table shows the current consumption of Radio. What's difference w/ Iradio_tx0 and Is0? Why do we get...
Dear Nordic Team,
We are building a very low power wearable with the nRF52810, only powered by a small solar cell and a super-capacitor.
We would like to offer firmware...
Hey,
I am working on nRF52 DK boards. Suddenly PC is not detecting the one of my DK board, but the nrf53832 processor's LEDs are functioning as per the last program dumped...
I am trying to use multiple channels for beacon transmission.I want to hop to a different channel at an interval of 2 seconds.I have configured one device as a pan coordinator...
Hello,
I'm using following code to read two channels of SAADC. It works fine when device is not connected to BLE central device. As soon as it's connected, the saadc_callback...
Hello,
I want to use 2 thingy:52 board in which one will act as master and other as slave. If yes, how can we do it? please provide any example code. Thank you.
hi guys, I'm looking for understand how to send a simple signal using ble mesh between two nrf52840 boards.
The available example aren't so usefull in order to have the...
I need to store a data base into an area of the FLASH. I understand I need to use the pstorage capability. All the reference I found about it , are just part of the code where...
Hi, I bought Sparkfun nrf52832 breakout board and i am having issues with programming a board.
I downloaded Segger embedded studio and nRFGo Studio for uploading hex files...
Hi,
I have set a Mesh Client Node with two BLE services: Mesh Proxy Service and Nordic Uart Service.
The problem is that when I send a message to the Mesh Client from...
