Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hey, I am working on the proximity application on nrf51 DK. How can I get the bsp_event_handler to get triggered on a button multi press (such as pressing button 1 twice rapidly...
Hi,
Do you have support for mobility in Cat-M on your nRF9160? This is usually done in RRC connected, but i'm wondering if you are able to support it in eDRX as well?...
Hello;
We are developing a project. And there must be three features in our project.
1) Should scan and transmit beacon at the sametime
2) Chip should read and write...
How can i read advertisement and not connect? I would like to do some checks on the advertising data within BLE event BLE_GAP_EVT_ADV_REPORT and then decide if i want to manually...
I am trying to transmit a modulated carrier with a high duty cycle but it does not work
the same command works with the default duty setting (50%).
The cli freezes when...
VUSB current consumption of the NRF52840: We have a setup where the 5V supply to this pin has very limited current capability.
What is the maximum current which can go into...
The Problem: HardFault within sd_softdevice_enable. With HardFault breakpoint enabled, the debugger halts at address 0x8C8. With this breakpoint disabled, breakpoints after...
I having trouble setting power level above +4 dbm in my app based on the example "ble_app_beacon" using the PCA10059 nRF52840 dongle. I have updated the main.c with the following...
Hi, i'm designing a device which is based on nrf52832 chip and i need to add two IC on my board, the first one is the MAX8856 to charge the battery of my device and the second...
I want to execute timer interrupt at a certain interval, like 1sec or 5 sec.
I measured an actual interval of voltage change with oscilloscope, but the actual interval is...
Hello
i have nrf 51822 beacon and i need to setup beacon that he send out data and i scan it without connecting-read brcst data.
i scan microchip 4870 and other beacon...
What is the best method for attempting to recover from a stuck TWI bus after init?
I am currently initializing the TWI instance with .clear_bus_init=true but this only...
I just finished upgrading the SDK version from v14.2 to v15.3, one thing I'm having trouble with is that after secure buttonless DFU finishes the call to `sd_softdevice_disable...
I'm testing this with SDK 15.2 on an NRF52832, with SD132.
I'm trying to implement error handling for FDS, but some cases are not clear to me how to deal with them.
Am...
We are working with DK nrf 52840 and the sdk mesh 3.0, BT sdk version is15.2 (dimming server example).
We noticed that when nordic app(nrf mesh - android) send a generic...
