I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Dear Sir
I'd like to develop the Window APP for Mesh (like nRF Mesh).
And I've face a problem. The ECDHSecret key of the Windows side didn't match the device side(Thingy...
Hi everybody!
I am new to programming with Nordic SDK and have some questions regarding writing applications with secure and buttonless DFU via BLE.
I have looked through...
I am using NRF52840DK with SDK15.2 to test the DFU.
I use Segger Embedded Studio to compile both the secure_bootloader project and ble_app_buttonless_dfu project.
Then...
Hello,
Is there any development board like an Arduino mini for the nrF52840. It need to fit a in very small enclosure
Ideally, I would like to test/develop some sensors...
Hi,
I am working with hid keyboard example on my Windows machine.
Problem 1 : After flashing the code, I make bluetooth connection and the code works properly. Then I...
Hi,
I am reading the Product Specification v1.3 of the nRF52832 SoC.
On page 23 the RAM0 block section 1 address is given as 0x21001000.
From the context I believe, this...
As per one of my discussions with , on another thread here , I can send a GenericOnOffGet from my android activity and I will get the status of the light in GenericOnOffStatus...
Again!!! I have a lot of problems to navigate on the Nordic products.
I follow the links and went to the start52840dongle and downloaded the SDK.
I find only stuff regarding...
Hi,
In looking down the road for product enhancements and migration to the 5.0 Bluetooth specification. I am interested and wondering if any discussion about chipset production...
Hi there,
one quick one:
when configured as SYSTEM RESET, Does P0.18 acts as an Input/Output? i.e. will be asserted Low by the NRF52840 while the MCU is in reset?
...
Hi all,
I'm using ble_app_multirole_lesc example to develop my application, it connect to android phone as peripheral role and now I need it to connect to another nrf52832...
If I have the J-Link RTT Viewer open and connected to my PCA10056 (viewing RTT output from an external board connected to P19) and then reprogram the board using nrfjprog...
Hello,
I am currently running into an issue with nrf51822. I am trying to write in flash a flag which defines the device I use. Indeeed, the device on which the code will...
Hello,
I want to us the nRF52 dongle with BLE and ANT communication. I downloaded SDK 15.2 and looked at the examples. I can see a lot of examples for ANT and for BLE individually...
