Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hello all,
I am using nRF52810 programming in segger embedded studio in windows 7. I am refer SDK nRF5 v5.2.0. I am trying to do i2c communication between sensor and nRF52810...
I had a couple of questions regarding the SPI slave peripheral on NRF52:
What is the behavior of the peripheral if a transaction completes (NSS goes high) and another...
I used the example code of MQTT pub and sub with nRF52 DK which has nRF52832 in it. I have sent the data from one kit to another with the help of Raspberry pi 3 as a router...
Hello. I need a bit of help with my case. I have nRF52832 dev kit. I have set heap size to zero in Makefile:
And even with that change I am still able to allocate memory...
Hello,
I have some questions about NFC on nRF52832:
1.Could NFC on 52832 works as a card reader , for the mifare 1 card, or named S50 card?
2.In the example "nRF5_SDK_15...
Hi all,
I have read that ANTUSB-m is needed for ANTWARE running in Windows PC. Can I use nRF52840 DK or nF52840 USB dongle in place of ANTUSB-m? If yes, where I can find...
Hi all
I have a custom Board, I have tested it a lot. NRF51822, programed with Mbed..
In general the Software and Board WORKS FINE, but I found some problem in my procedure...
Hello
I am following example on :
examples/dfu/secure_dfu_test_images/ble/nrf52832
when flashing:
sd_s132_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
Hello,
I'm trying to use this code https://github.com/kimyd/SHT1X_on_nrf51822 to communicate with an SHT11 sensor via GPIO pins. I have a Saleae hooked up an can see the...
Our project uses nRF51822 with SDK12.3.0 and s130. We are using app_timer_appsh.h and app_scheduler.h to make a "UTC timer" by counting a static variable each 1S timeout ...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10
when I debug the pairing function,the phone displays one dialog box about Bluetooth...
Based on nrf52832 development nrf as a tag, the actual distance is 2 cm, less than 3 cm with a reader, how to improve for it? Let the distance of nfc exceed 3 cm?
Hello everyone,
I am refering to https://devzone.nordicsemi.com/f/nordic-q-a/29029/programming-nrf52-with-openocd/126175#126175
Is there any complete tutorial out there...
Hi. I'm currently working on a project using nrfx_uart driver. I'm using the project template for SES provided in the examples folder.
My Issue is that my code only works...
