Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Does anyone know when will ANT SoftDevice be available for nRF5 SDK v15? Accordign to https://www.thisisant.com/developer/components/nrf52832#tab_protocol_stacks_tab, only...
Hi
I try to communicate with my NRF24L01+. For this, i have connected a mikrocontroller to my Module. Actually i am using a small piece of code, which allows me to send...
Hi,
In my project, I use button for put on the microcontroller in sleep mode. I implemented one timer that when I press more of 5 second the button, the micro call sleep_mode_enter...
Hi,
I have included in my code the code from the twi_scanner example as a starting point for using TWI in my board. When compiling, I get the following error:
../.....
hi,
Please Refer Light Switch Client Example in Mesh 2.0
I would like to know Code where and in which File the UUID from the unprovisioned Node is captured ?
Thank ...
Hello,
What is the switching frequency of the buck regulator integrated into the nRF51822?
The characteristics of this regulator do not seem to be explained in the documentation...
I'm following the Custom BLE Service Example , and using:
Segger Embedded Studio Release 3.34a
macOS 10.13.4 (aka High Sierra)
nRF52 DK (PCA10040, nRF52832)
nRF5_SDK_15...
Hi,
I am investigating an alternative to an implantable device that currently uses NFC.
The device range would only be about 3m and the data would only be transmitted...
this packet is capture by wireshark .I use nrf51822 and sdk12.3 connect Balance car,but the packet not have LL_VERSION_IND, LL_FEATRUE_REQ、and LL_Connect_UPDATA_REQ these...
Dear Nordic Team,
Thanks for supporting.
now i am workwith secure dfu. I followed this link https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure...
hello
I am just starting to use the nrf52832 .
I design the PCB with nrf52832 and want to load the softdevice.The nrf go studio can not detect the nrf52832, but the keil...
I was facing some issues getting PWM peripheral work on my custom nRF52840 board. And then I tried the pwm output on P0.08 instead of P0.06 and the signal came out just fine...
We're developing a new device for a regulated market (medical). As such, we need to have control on what third-party software we're using, and how it is working. While starting...
I wanna implement this code for the app inventor, but there was several problem here. I can't use array or index for developing my trapezoidal method.. like this..
code...
