Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hello - I tried looking for my answer here but didn't really get what I need. I'm also relatively new to all of this.
I purchased the Adafruit's nRF8001 bluetooth module...
hi
i am using nrf52 dk wiht IAR embedded workbench IDE ARM 8.20.1
i want to disable the attach to running target from my device HZX-52832-S01A.
which bit i have to turn...
Hello.
I am measuring the current of nRF52832 using Power Profiler Kit (PPK).
I want to change the voltage supplied to nrf 52 arbitrarily.
I used the following case...
Hi everyone!
How to change erase range in DFU during application upgrade ? I have some data saved in flash (by psotage on 0x0007e000) and I don't want to lose them after...
Hi,
What is the advantage of using a Bluetooth SIG defined profile over a vendor specific profile? For example, if we want to transfer battery levels, can we define our...
Hi again,
Hope everyone had a great Christmas.. I did, but Santa also gave me a litte issue with my nRF52-DK..
I using a modified UART example, I have a 5min repeating...
Hello,
Basically my arrangement of NRF network is one receiver and multiple transmitter consider example 1:40 and they all configured with same address,bitrate, checksum...
Hello,
Is there a demo project that contains RTC function with softdevice.
I called the lfclk_config() and rtc_config() function before softdevice initial in main(), but...
I am using nrf52832 chip. I will be receiving time in isoFormat.
I am wondering how convert the iso format to get the date and time in my C program.
I am not using any...
Hi,
I'm develope some sensor with arduino primo, which use nrf52832 as a primary mcu.
I want to measure battery voltage level,and i find some example like:
devzone.nordicsemi...
I am using nrf52832_xxaa with SDK v11.0.
I have a requirement to write into UICR register APPROTECT to set its value to 0x00.
Is it possible?If yes, please provide a sample...
hi,
10040 nrf52dk
softdevice 132 v2.
keil ide
I am trying to read magnetometer values so that i can calibrate it using this method . For this to happen, i need magnetometer...
Hi guys,
I am using FDS module in nrf51822, sdk 11 to store and read data from flash. I have a problem about reading the data. In the documents, the function:
fds_record_open...
