I'm currently evaluating the Shorter Connection Intervals feature of BT 6.2, and its use for low-latency HID applications. I have seen the updated HID mouse sample ( https...
Hello,
I am debugging a custom board that uses an nRF7002 connected to an nRF54L15. The nRF7002 power-up sequence appears to be working correctly, but the device does not...
Hi Håkon,
this is my follow-up ticket as requested here:
You can see my setup in the esb_ptx application in https://github.com/stemschmidt/esb-evaluation.git
I am currently...
SDK: nRF Connect SDK v3.3.1 Zephyr: v4.3.99 Board: nrf7002 DK I'm implementing a WebSocket server using the Zephyr HTTP server. The callback looks like: static int ws_connected_cb...
Hi
nRF54L15-DK QFAAC0, ncs v3.4.0, project path: ncs\v3.4.0\zephyr\samples\boards\nordic\system_off
After compiling and flashing this example, the power-on reset (POR...
I am looking to evaluate Amazon sidewalk on the nrf54L15 dev kit and have also bought both of the Semtech evaluation boards LR1110MB1LCKS and SX1262MB2CAS. The nrf54L15 is...
The nRF54L15 Product Specification lists the following PDM feature:
"8 kHz, 16 kHz, 32 kHz, or 48 kHz output sample rate" "Supports digital microphone clocks at 768 kHz...
I use `west debug` to start `gdb` for debugging nRF5340DK
when I use `west build` to update the image, I use `load` command inside gdb CLI, the new `zephyr.elf` is loaded...
I don't know if this is a hardware or a software problem. My nRF52832 code runs correctly on a PCA10040 development board (UUID = E9:4A:AF:04:D2:16). My custom hardware advertises...
My software sent 2422, and I saw it on the net. 2417 also has one.
And the same goes for everything else, which is basically 5M off.
What is the reason?
Hi all,
I am working on troubleshooting intermittent application resets with an nRF52840 and nRF Connect 2.6.1. Codebase is small, complexity of the project is still small...
Hello,
I'm working on a BLE central multilink application, where I want to get the list of all peripherals in range, In order to let the user select the needed periherals...
I implemented UART communication as follows, but occasionally the same data is sent twice.
Enter the critical region (app_util_critical_region_enter).
Store the transmission...
hello!
I'm using 'NRFX_LOG_INFO' for debugging purposes. However, the code seems to stop progressing when 'the NRFX_LOG_INFO' statement is removed from the section below...
Hi,
I am using an nRF52 DK board to perform some very simple tests. All I need to do is receive a line of text over serial, perform some calculations and return another...
HI
I'm trying to use lpcom to detect when the battery voltage is dropping.
The configuration is as follows: 5V battery voltage output is reduced to 3.0V through LDO...
For my application I need the UART TX/RX pins pulled low until I am ready to turn on the UART. Is there a method in Zephyr to do this? Currently when Zephyr starts it reads...
I saw some similar question, but none is what I am experiencing.
I notice some weird behavior while testing DMA mode, so I made a simple setup:
I set the DMA buffer to...
Hello everyone,
I have two devices: a Thingy53 acting as the peripheral and an nRF5340 acting as the central. I have a characteristic in a service that I want to modify...
can I send the data from the internal sensors of the stm32l4 card to nordic thnigy 91, then the latter send the data from its internal sensors and the data which is already...
