Hello Nordic team,
What is the image frequency of the nRF54L15 receiver?
We need this information for Bluetooth SIG RF-PHY qualification (RFPHY/RCV/BV-03-C, RFPHY/RCV...
Our prototype is back. At first, I used NRF Connect to flash it, but the official PC software couldn't flash the firmware. I followed the wiring instructions: (1) connect...
We are developing an application based on the nRF9151 using NCS 3.1.1 and modem firmware mfw_nrf91x1_2.0.3 .
We would like to use Proprietary PSM to control the modem's...
Hello, The nRF9151 hardware design guidelines (power sequence) require VDD_GPIO to be applied at least 6 ms after VDD and ENABLE, after the hardware boot. In our design a...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
I have recently upgraded my SDK from NCS V2.2.0 to V2.6.0, and have come back to some firmware I had working under 2.2.0 as I need to progress that. The firmware is based...
You may ask what poolside means. It means at my community pool, where I don't have Internet access via Wi-Fi for my laptop.
I wish to run some AT commands like AT%NCELLMEAS...
Hi, I have followed the instructions in Securely generating credentials for nRF91 Series devices - nRF Cloud but cannot connect to nRF Cloud.
I think the instructions on...
Hello everyone,
I've been spending a lot of time to fix the issue not being able to enter DFU mode with the following error. I've changed so many versions of GCC, but it...
Dear Nordic devzone community,
I have designed a custom board using nRF9160 and I am able to send and read out certain AT commands which confirms to me that most of the...
I'm transitioning from SES to Visual Studio Code.
In SES, I can define multiple builds and then define preprocessor options (eg. -DOPTION1) for each build definition
I...
Hi there,
We are quite new to Zephyr. We are currently porting our existing app onto Zephyr as a test. We are currently using NCS 2.5.1
So for our existing application...
I needed to add my own partition to the primary flash, and was able to do so successfully by adding a section to the device tree partitions.
However, when adding MCUBoot...
Hi,
I'm trying to setup my NFR52840 DK to act as a NFC tag so that I can read some simple data on my phone via NFC transfer.
I have tried a few NFC sample applications...
Hi,
I am using a modified HTTPS Client demo code [Let's say Version A] and sometimes when trying to debug with Segger Embedded Studio for ARM (Nordic Edition v 5.34a/Jlink...
Hello,
From time to time I am getting the error " Unable to find bootable image" when I start a debug session in SES-NE v5.60.
FIH_CALL(boot_go, fih_rc, &rsp); if (fih_not_eq...
I am trying to read the GPIO state on an nRF52840 right after it wakes up from deep sleep (System OFF mode). I have configured 4 pins as wake-up sources from deep sleep System...
I have been working on finding the cause to an unexpectedly high power power consumption in several newly produced units of our product based on nRF5340. I believe I have...
I'm trying to build a custom secure partition, but get the following error when building:
However when navigating in files to the directory the file "tfm_custompartitiontest...
Hi All,
My team recently reserved a custom service UUID with the Bluetooth SIG, and we'd like to replace the custom 128-bit UUID we had been using in our products. Can I...