I tried the suggestions on https://devzone.nordicsemi.com/f/nordic-q-a/110615/on-connecting-any-nordic-dk-board-to-my-mac-the-link-volume-starts-mounting-and-unmounting-forever...
Hi,
I want to connect X-NUCLEO-NFC08A1 with ST25R3916B to nRF5340 board by adding a SPI node to device-tree source. After compiling and flashing the board, triggering interrupt...
Hardware is nrf5340DKI
nrfconnect v2.6.0
zcbor library 0.8.1.
I'm running a project on the nrf5340 DK that is using the zcbor library to encode log events. The cddl...
Is it possible to use configure MPSL to use multiple FEMs? I see that you can configure it to use a simple GPIO interface, which works fine for a single FEM with fixed gain...
Hello,
I have a custom board running as a low power node, consuming around 17uA during sleep. When I have messages back and forth, the node goes back to sleep as usual....
Hi,
I am writing to seek guidance regarding the implementation of Modbus communication on the nRF9160 Development Kit.
As a developer who is relatively new to the concept...
for the nRF52840
does Nordic have .s2p file for simulating the frequency spread and Gain/Loss (S21, S11, S22) Characteristics of the chip.
also any reference to an internal...
I am trying to use the Peripheral_Uart application and when it runs, I see 2 virtual com ports in Windows device manager.
A terminal program shows a startup status message...
My main goal is to update the firmware over FOTA on a nRF5340, but with a signed firmware update file, and the bootloader verifies it. This is possible with mcuboot and works...
Hi,
We have implemented USB DFU on NRF52840 successfully. We have downloaded the "nrfutil" exe in winodws laptop and I am able to do OTA via USB using the command mentioned...
I'm doing a project for adding a Bluetooth capability to an embedded Linux device. The Linux master talks to the nRF52840-based Bluetooth module via a dedicated serial (UART...
I've got a project that I'm going to want to do DFU through the UART, and in order to transfer files in a follow-on activity, I want SMP running in the application. Therefore...
HI Nordic support team.
I have a question relate to TX power in ANT application:
- ANT Tx application using: ant_broadcast ->Tx
- ANT Rx application using: ant_continuous_scanning_controller...
I'm using an nRF52840 and SPI 15.3 here..
What I'd like to do is to have SPI write (at 10 Mbps) 8 transactions of 2 bytes each every 91uS and do that for say 512 times before...
Hello,
I have (2) Questions below highligted in yellow
I have followed these steps until Step 5 Substep (1-4)
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
I am using pin 8 (NFC pin) as SCL and pin 9 as SDA of nrf52832 on my custom board. Basically I have connected MPU9250 with these pins and I know that MPU9250 is NRFND, for...
I'm doing a project for adding a Bluetooth capability to an embedded Linux device. The Linux master talks to the nRF52840-based Bluetooth module via a dedicated serial (UART...
I am running a copy of the Peripheral_UART application on a nRF52 Dev Board (Segger PCA10040)
The device connects to iOS apps (such as nRF Connect and nRF Toolbox.
I can...
Hi
For nRF7002-DK, SDK Version 2.52,I gernate gpio port and set it as active low as below. after gpio pin set as active low, on debugging mode occurred exception fatal error...
Hi,
I want to add some build information (hard coded) into my binary. Is there any way how I can access the current date/time and maybe the revision number of a SVN repository...
The MCUboot, Slot0, and Slot1 flash partitions are defined in the board file. E.g., nrf52840dk_nrf52840.dts has boot_partition at 0 with length 0xC000, slot0_partition at...
If I'm building an iOS app to connect to a nRF5340 device and want to build DFU/FOTA into my app. I used the IOS-nRF-Connect app and followed the FOTA over Bluetooth Low Energy...