hi support team,
customer is testing our nrf93M1 module, and find out, when device enters system mode after sleep, there will be a lot of URL sending to UART as below: ...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
Hi - I am trying to commission my NRF5340DK board with NRF Connect SDK v.2.1.1 using Google Home App over Matter using the Matter light bulb sample.
My OTBR is a Google...
Hello,
When I starts my SLM application with lwm2m carrier library, I receive this right away:
My issue is that I don't want modem to start in active (CFUN=1) mode...
Hello Team,
We are currently experiencing an issue with the PPK II.
Yesterday, we updated the software, including a Bluetooth low energy update in the nrf desktop app...
Hi,
I am trying to develop an MP3 player I want to configure LRCK to 44100 but I only able to configure it to 43530 with configuration available in document as CONFIG.RATIO...
Hi,
Set the module mode to CAT-M1
Please provide the highest frequency B1 B3 B8 B19
Please provide B1 B3 B8 B19 lowest frequency
Please provide B1 B3 B8 B19 center...
Hi everyone:
I developed an application based on freertos, but when I download it, I found it can not start, but when I use the RTT to connect my device, It worked.
The...
I selected "All boards", but the nrf52840dk board is not listed. I have tried uninstalling and reinstalling the nRF Connect extensions in VS Code, but the nrf52840dk board...
I want to use public-addr and non-resolvable-addr for advertising on nrf connect SDK.
I was able to advertise using a random static addr.
But, 1. can not set public addr...
hi I am configuring a BLE peripheral using NCS v2.2.99-dev3 and the nRF5340 DK. I want to set the security level of the device to mode1, level 4 for cyber security. I searched...
Hi team!
I have some doubts regarding updating the advertising data using periodic advertisements. We were able to advertise 1,650 bytes of data using periodic advertisements...
hello Nordic
i am working with nrf52832 with ncs v1.9.2 with zephyr
i am using spim to read from a sensor
the spi xfer command is done via ppi with a timer ~20kHz
...
We are using Segger Embedded Studio with a few different nRF SDKs (15.3.0, 16.0.0. 17.1.0) and MCUs (nRF52810, nRF52832, nRF52840). We are setting values for RAM_START and...
Hi,
I am running the following example from the SDK for Thread v4.1.0: IOT/DNS and followed the SDK instructions to setup the BLE devices as well as an Ubuntu VM acting...
Hi team !
I'm facing issue when porting my code from nRF52840DK to nRF5340DK
I implemented SAADC acquisition, using Timer/SAADC/(D)PPI stack on both boards, handling...
Hi, I can get ahold of the SPI device and call the spi_transceive function wihtout returning error codes. Logic analyzer shows nothing happening, such as SCK clocking. I am...
