We are migrating following your November 11 notice. Two read-only Identity Service operations remain unresolved:
- POST api.identity.nrfcloud.com/.../verify-jwt authenticates...
hi support team,
customer is testing our nrf93M1 module, and find out, when device enters system mode after sleep, there will be a lot of URL sending to UART as below: ...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Dear Team,
I have been running two nRF54LM20-DK as Initiator and Reflector for Bluetooth Channel Sounding.
I adjusted the ranging algorithm RAS_Initiator to print Local...
Hi,
I'm trying to find out how people automate current measurements with the PPK2 beyond doing it by hand in the Power Profiler app.
From the threads here it looks like...
During the setup process for nRF Connect SDK v2.4.0, an error occurred preventing the SDK from installing correctly.
The environment details are as follows:
* macOS...
I am trying to debug the nrf9160 with the swd interface.
I can read and write to the private peripheral addresses (0xe000_0000 and up) but i cant write or read to any other...
Hi,
I wanted to know that is there any example code for the power management. how we can enter into the stanby mode and how to come back to active mode, time required...
Hi,
I had been read the white paper and it comes to antenna switching patterns. White Paper its tells me:
With a linear array of 4 antennae and their gpio pattern 0...
Hi,
I installed latest nRF connect for desktop application in my windows 11. After installation it seems the window is completely stuck and does not load anything.
Tried...
Hi
The Wi-Fi provisioner app won't connect to my DK board.
I've flashed this hex file:
https://nsscprodmedia.blob.core.windows.net/prod/software-and-other-downloads...
I have a setup what startups up a device in CLI mode (UART + RTT) when certain test condition set at bootup.
However, I implemented a command to "uninitialize" CLI mode...
Hi,
I am modifying the peripheral_uart code to set a fixed pairing method so that I will have to enter a pre-defined passkey in my nrf connect application on my android...
Hi, I am sending data from AWS and run it through cJSON_Parse(). If the message is just a little bigger than 1000 bytes, I will get the message "cJSON Parse failure". Debugging...
Hello, I am trying to capture the analog signal from two pins.
From one channel, I could get a signal with up to a 2kHz sampling rate.
However, the problem is, I couldn...
I'm using a custom board that has nRF52810 and lis2dh12 sensor. The sensor's Vdd is powered from a GPIO (configured a regulator-fixed to supply power from the GPIO during...
Hello,
I've been waiting for a response to this post for a month, but got no suggestions.
So I created this new case for it.
I am using nrf5340dk board to test KSCAN...
hi,
We need to test nrf7002 2.4g and 5g single wave, but I can't find demo in ncs v2.2.99-dev3, nrf\samples\wifi\radio_test is packet transmission.
We can only find some...
When I execute the command: west build -p -b thingy91_nrf9160_ns -- -DDTC_OVERLAY_FILE=ppp.overlay -DOVERLAY_CONFIG=overlay-ppp.conf
I get:
ld.bfd: region `FLASH' overflowed...
I have problem with BLE connection. I developing a BLE Gatt client application with ESP32. There is a nordic processor in my sensor (end device).
Notify is not coming to...
Hi Nordic Team
I tried to get the USB Dongle PCA10049 to connect on a other device (PCA10056) over custom UUID and Custom characteristics.
I used the Example from Dev...
